YASKAWA CIMR-JT Series User Manual

Parameter Setting Range Error ..................... 136
Parameter Settings ..................................90
PASS ........................................135, 150
Password ........................................ 223
Password Setting ................................. 223
Password Settings ................................ 124
Peak Hold Current ............................118, 245
Peripheral Devices Affected by Drive Operation .... 164
PF ...........................................135, 145
Phase Order Selection............................. 224
Poor Speed Control Accuracy...................... 160
Power Specifications 200 V Class Models .......... 211
Power Specifications 400 V Class Models .......... 213
Previous Fault ................................118, 245
Programming Mode..........................85, 87, 88
Protective Covers, Reattaching..................... 207
Protective Covers, Removing ...................48, 206
PWM Feedback Data Fault ........................ 134
PWM Feedback Fault ............................. 139
R
RAM Fault ....................................... 134
Ramp to Stop.......................................98
Rated Frequency..............................211, 213
Rated Output Capacity (kVA) ..................... 211
Rated Voltage ................................211, 213
REMOTE ..........................................91
Replacement Parts ................................ 219
Restart Enabled................................... 234
Reverse Direction................................. 234
Reverse Operation Selection ....................... 224
Reverse Run Command (2-Wire sequence) ......... 233
rH ...........................................135, 145
RTS Control Selection ............................ 236
Run command ......................................99
Run Command/Frequency Reference Source Selection
Error............................................. 153
Run Command at Power Up ....................... 224
Run Command Input Error ........................ 135
Run Command Input Selection.......................96
Run Command Selection ......................157, 224
Run Command Selection during Program........... 224
Run Command Selection Error..................... 136
S
S1 .................................................97
S2 .................................................97
Safety Hazard Definitions ...........................14
Safety Information ..................................14
S-Curve Characteristic at Accel End................ 226
S-Curve Characteristic at Accel Start ............... 226
S-Curve Characteristic at Decel End................ 226
S-Curve Characteristic at Decel Start ............... 226
S-Curve Characteristics .......................100, 132
SE ...........................................135, 150
Serial Communication Reference Selection ......... 232
Serial Communication Transmission Error ......135, 147
Setup Mode .................................... 87, 92
Shielded Twisted-Pair Cables........................62
Side-by-Side Setup .................................35
Sinking/Sourcing Mode Switch ......................28
Slip Compensation Gain........................... 226
Slip Compensation Primary Delay Time ............ 226
Soft Charge Circuit Fault .......................... 135
Soft Current Limit Selection ....................... 240
Software No. (Flash) .............................. 244
Software No. (ROM).............................. 244
Software Number (Flash).......................... 118
Software Number (ROM) ......................... 118
Speed Agreement Detection Level ................. 238
Speed Search ..................................... 234
Stall Prevention................................... 132
Stall Prevention During Deceleration .................70
Stall Prevention Level during Acceleration ......... 238
Stall Prevention Level during Run ................. 238
Stall Prevention Selection during Acceleration ...... 238
Stall Prevention Selection during Deceleration ...... 238
Stall Prevention Selection during Run .............. 238
Standard Connection Diagram ................... 43, 44
STOP Key Function Selection ..................... 241
Stopping Method ...................................98
Stopping Method After Communication Error....... 236
Stopping Method Selection ........................ 224
T
Terminal A1 Bias Setting.......................... 234
Terminal A1 Gain Setting ......................... 234
Terminal A1 Input Voltage ........................ 118
Terminal A1 Signal Level Selection ................ 234
Terminal Block Configuration .......................47
Terminal Board Wiring Guide .......................62
Terminal M1 thru M2 Function Selection (relay) .... 111
Index
YASKAWA ELECTRIC TOEP C710606 25D YASKAWA AC Drive J1000 Installation & Start-Up Manual
283

YASKAWA CIMR-JT Series Specifications

General

Brand	YASKAWA
Model	CIMR-JT Series
Category	Controller
Language	English