10.2 Operation of Digital Operator
10.2.2 Operation of Utility Functions
10-10
Details on How to Set Table Settings
Details on the setting method for step 5 in Editing Program Table on page 10-8 are shown
below.
POS: Target Position
Note: Refer to the following section for details on positioning types and target positions.
7.3.4 Settings in the Program Table on page 7-13
SPD: Positioning Speed
Note: Refer to the following section for details on the positioning speed.
7.3.4 Settings in the Program Table on page 7-13
RDST: Registration Distance
Note: Refer to the following section for details on the registration distance.
7.3.4 Settings in the Program Table on page 7-13
RSPD: Registration Speed
Note: Refer to the following section for details on the registration speed.
7.3.4 Settings in the Program Table on page 7-13
㹎㸮㸮㸮㸻㹑㸩㸯㸰㸱㸲㸳㸴㸵㸶
㹎㸮㸮㸮㸻㸩㹇㹌㹄㹇㹌㹇㹒㹃
㹎㸮㸮㸮㸻㸫㹇㹌㹄㹇㹌㹇㹒㹃
㹎㸮㸮㸮㸻㸫㸫㸫
㹎㸮㸮㸮㸻㹑㸩㸯㸰㸱㸲㸳㸴㸵㸶
Move cursor
Change target position
㹎㸮㸮㸮㸻㹑㸩㸰㸰㸱㸲㸳㸴㸵㸶
㹎㸮㸮㸮㸻㸿㸩㸯㸰㸱㸲㸳㸴㸵㸶
Move cursor
㹎㸮㸮㸮㸻㸿㸩㸰㸰㸱㸲㸳㸴㸵㸶
Change target position
㹎㸮㸮㸮㸻㹇㸩㸯㸰㸱㸲㸳㸴㸵㸶
㹎㸮㸮㸮㸻㹇㸩㸯㸰㸱㸲㸳㸴㸵㸶
Move cursor
㹎㸮㸮㸮㸻㹇㸩㸰㸰㸱㸲㸳㸴㸵㸶
Change target position
㹎㸮㸮㸮㸻㹑㹒㹍㹎
㹎㸮㸮㸮㸻㸿㸩㸯㸰㸱㸲㸳㸴㸵㸶
Change positioning
type
Change positioning
type
Change positioning
type
Change positioning
type
Change positioning
type
Change positioning
type
㹑㹎㹂㸮㸮㸮㸻㸯㸰㸱㸲㸳㸴㸵㸶
㹑㹎㹂㸮㸮㸮㸻㸯㸰 㸱㸲㸳㸴㸵㸶
Move cursor Change positioning speed
㹑㹎㹂㸮㸮㸮㸻㸯㸱 㸱㸲㸳㸴㸵㸶
㹐㹑㹒㸮㸮㸮㸻㸯㸰㸱㸲㸳㸴㸵㸶
㹐㹑㹒㸮㸮㸮㸻㸯㸰 㸱㸲㸳㸴㸵㸶
Move cursor Change registration distance
If the value becomes less than 0,
“−” is displayed.
㹐㹑㹒㸮㸮㸮㸻㸯㸱㸱㸲㸳㸴㸵㸶
㹐㹑㹎㸮㸮㸮㸻㸯㸰㸱㸲㸳㸴㸵㸶
㹐㹑㹎㸮㸮㸮㸻㸯㸰㸱㸲㸳㸴㸵㸶
Move cursor Change registration speed
㹐㹑㹎㸮㸮㸮㸻㸯㸱㸱㸲㸳㸴㸵㸶
To Next Page
Loading...
