10.2 Operation of Digital Operator
10.2.2 Operation of Utility Functions
10-9
Method for Moving the Cursor
The values within the frames in the figure below are the articles and steps of the program table
displayed at the digital operator.
3
Move the cursor using the keys and
keys (or the + and +
keys) to select the article and program step of the
program table to be edited. Refer to the following
section for details on the methods to move the
cursor.
Method for Moving the Cursor on page 10-9
4
Press the key to move the cursor to the set-
ting side of the table.
5
Move the cursor with the keys, and
change the table settings with the keys.*
Refer to the following section for detailed setting
methods for each item.
Details on How to Set Table Settings on page
10-10
6
Press the key to enter the setting. The cursor
returns to the program table article and program
step side.
7
Repeat steps 3 to 6 to set the program table. On completing the setting of all the program tables to
be used, save the program tables to flash memory by following the procedure in
Saving Program
Tables.
* If setting is attempted in an operation prohibited state, it will not be possible to change the setting. In this case,
make the setting again by referring to
Preparation.
Continued from previous page.
Step Display after Operation Keys Operation
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧭㧯㧯㧜㧜㧞㧩㧦
㧭㧯㧯㧜㧜㧟㧩㧦
㧭㧯㧯㧜㧜㧠㧩㧦
㧭㧯㧯㧜㧜㧡㧩㧦
+
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧭㧯㧯㧜㧜㧞㧩㧦
㧭㧯㧯㧜㧜㧟㧩㧦
㧭㧯㧯㧜㧜㧠㧩㧦
㧭㧯㧯㧜㧜㧡㧩㧦
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧭㧯㧯㧜㧜㧞㧩㧦
㧭㧯㧯㧜㧜㧟㧩㧦
㧭㧯㧯㧜㧜㧠㧩㧦
㧭㧯㧯㧜㧜㧡㧩㧜㧜㧜㧜㧝㧜㧜㧜
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧭㧯㧯㧜㧜㧞㧩㧦
㧭㧯㧯㧜㧜㧟㧩㧦
㧭㧯㧯㧜㧜㧠㧩㧦
㧭㧯㧯㧜㧜㧡㧩㧜㧜㧜㧜㧝㧜㧜㧜
PGMSTEP POSSPD RDSTRSPD POUT
0 P000 SPD000 RST000 RSP000 POUT000
1 P001 SPD001 RST001 RSPD001 POUT001
2 P002 SPD002 RST002 RSPD002 POUT002
3 P003 SPD003 RST003 RSPD003 POUT003
4 P004 SPD004 RST004 RSPD004 POUT004
5 P005 SPD005 RST005 RSPD005 POUT005
6 P006 SPD006 RST006 RSPD006 POUT006
255 P255 SPD255 RST255 RSP255 POUT255
PGMSTEP POSSPD RDSTRSPD POUT
0 P000 SPD000 RST000 RSP000 POUT000
1 P001 SPD001 RST001 RSP001 POUT001
2 P002 SPD002 RST002 RSPD002 POUT002
3 P003 SPD003 RST003 RSPD003 POUT003
4 P004 SPD004 RST004 RSP004 POUT004
5 P005 SPD005 RST005 RSP005 POUT005
6 P006 SPD006 RST006 RSP006 POUT006
255 P255 SPD255 RST255 RSP255 POUT255
PGMSTEP POSSPD RDSTRSPPOUT
0 P000 SPD000 RST000 RSP000 POUT000
1 P001 SPD001 RST001 RSPD001 POUT00
2 P002 SPD002 RST002 RSPD002 POUT00
3 P003SPD003 RST003 RSPD003 POUT00
4 P004 SPD004 RST004 RSPD004 POUT00
5 P005 SPD005 RST005 RSP005 POUT005
6 P006 SPD006 RST006 RSP006 POUT006
255 P255 SPD255 RST255 RSP255 POUT25
Moves the displayed rows up or down one row at a time.*
On reaching step 0, the next movement is to step 31.
On reaching step 31, the next movement is to step 0.
Moves the displayed
column one column at a
time to the left or right.
On reaching the edge of
the table, movement
stops.
To Next Page
Loading...
