YASKAWA yasnac lx3 - Page 228

APPENDIX 1 LIST OF SEITING NUMBERS (Cent’d)
I
\
-l—
,.——
r
I D, 06
––
L
D7
Cut Depth
Override
D5 D1
I
._— —
COV 16 I COV 8 I ~ COV41 COV21 Covll
0100
0 0
100%
~- .-—---- .
ISOEIA
o
I
0,0
0
1 1o%
—
20%
30%
1: Punches out tape code with 1S0
code.
code.
o ~ o *O
1 0
. ..—
0: Punches out tape code with EIA
TVCHK D6
1: Executes TV check.
o: Does not execute TV check.
UM09000E D5
o
0
I
o
1 1
—-–..—. -—
.
0
Oit 0’0
40%
0
0’1 50%
—+ -——
.2
l~o
u- ‘L- ‘-——
60°10
70%
0101
Ill
.. —
L. —4
80%
900/o
1: Effective on the edit interlock in 09000!s.
.——..
--—+
+
0’1
0
.-L.
o
.——
0
1
0
1;1
1Oo%
11o%
o: Ineffective on the edit interlock in 09000’s.
UMO18000E D4
1:
Effective on the edit interlock in 08000’s
o:
Ineffective on the edit interlock in 08000’s.
t -
- -~
Oil
1 0!0
120”/0
—
130”10
140%
L -—-——
011101
o
I
1
150%
1600/0
170”/0
1800/0
.—
r.l —
~eoo3
D5 Dd
[-D, DO
-L–-..
–—.–-...——
1>5, D4
ODvCE 1 Selects RS232C
ODVCD O 1/0 interface.
Dl, D()
IDVCE 1 Selects RS232C
IDVCE 0: port.
—
interface for output port.
+-
1 o~o_J1’1
-.——
1
Oil
I 0-- 0
190%
—.
200%
interface for input
Note: These settings are effective when parameter *6023 Dz
(COVP) is “O.”
Setting
Input/Output
Parameter No.
Code Port
requiring Baud
Rate Setting
UM08000
D2
1:
Inhibits editing and display and punchout opera-
tions of the part program of program NO. 8000 to
8999.
0:
Permits editing and display and punchout opera–
tions.
UMSBK
D1
1: Makes Single Block Stop effective for the
programs in user macro when single block
input is on.
O: Does not permit Single Block Stop for the
user macro blocks commanding operation and
control.
o
1
I
RS232C # 6026
No. 1
#6028
~
0,
RS 232 C
# 6027
No.1 # 6029
I
1
‘:{04icEE&-DmEE
COV161(D7), COV81(D6), COV41(D5)> COV21(D4),
COV11(D3) :
Sets the override of cut depth for Stock Removal
in ‘Turning (G71) and Stock Removal in Facing
(G72) cycles.
SKIPIN Do
1:
Executes the next block when the skip
signal is not given before completion of
movement of block including Skip Function
(G31) or if the touch switch does not trip
beyond the limit position in the direction
of motion for tool set error compensation
(G35).
o: Alarm “ 087” is displayed.