YASKAWA yasnac MX2

Depress
the
OUT
key.
The
paper
tape
punch
punches
the
tool
offset
data
onto
paper
tape
and
stops
auto¬
matically
when
all
contents
of
the tool
off¬
set
memory
have
been
output.
To
suspend
the
operation,
depress
the
RESET
key.
At
this
time,
the
output
operation
cannot
be
resumed. Restart
from
the
beginning.
E.
4.
*4.
2
INPUTTING
SETTING
DATA
AND
PARAM¬
ETER
DATA
Though
setting
data
and
parameter
data
are
nor¬
mally
input
by
MDI
operation,
they
may
also
be
entered
by
means
of
paper
tape.
Setting
data
and
parameter
data
may
be
input
from
a
single
tape
F.
The
tape
format
is
as
follows.
1
.
2.
The
tape
format
is
the
same as
that
describ¬
ed
in
4.4.1
INPUTTING
TOOL
OFFSETS
FROM
TAPE.
Label
%
;
#6000
XI
28
#6001
X
5
#6002
X
0
Note:
is
used
in
the
ISO
code
and
"ER"
m
the
EIA
code.
4.4.4
OUTPUTTING
SETTING
DATA
AND
PARAMETER
DATA
TO
PAPER
TAPE
The
output
operation
is
as
follows.
1.
Select
EDIT
mode.
Depress
the
RESET
key.
Depress
the
PRM
key.
Check
that
the
punch
is
ready
for
opera¬
tion
Depress
the
OUT
key.
The
paper
tape
punch
punches
the
setting/
parameter
data
onto
paper
tape
continuous-
A.
%
B.
C.
D.
2.
The
input
operation
is
as
follows.
A.
Select
EDIT
mode.
B.
Depress
the
RESET
key.
C.
Deprss
the
PRM
key.
D.
Set
the
setting
/parameter
data
tape
onto
the
tape
reader.
E.
Depress
IN
key.
The
tape
reader
starts
to
read the
tape.
"IN"
blinks
on
the
CRT
while
the
data
are
read.
F.
The
tape
reader
stops
when
it
has
read
"%"
(or
"ER").
"IN"
disappears
from
the
CRT.
Now
the
setting
/parameter
data
have
been
read
into
memory.
Turn
on
power
again
because
the
control
is
in
the
HOLD
state
(key
inoperative)
at
completion
of
input.
E.
iy-
To
suspend
the
operation,
depress
the
RESET
key.
At
this
time,
the
output
operation
cannot
be resumed. Restart
from
the
beginning.
F.
2.
The
tape
format
is the
same
as
that
described
in
4.4.2
INPUTTING
SETTING
DATA
AND
PARAMETER
DATA.
4.4.5
OUTPUTTING
PART
PROGRAM
TO
PAPER
TAPE
(1)
The
part
program
of
the
designated
program
number is
punched
out
by
the
following
operations
:
4.4.3
OUTPUTTING
TOOL
OFFSETS
TO
PAPER
TAPE
a.
Connect
the
external
equipment
such
as
the
tape
puncher
to
the
NC
via
the data
input
/output
interface.
b.
Make the
external
equipment
relay
for
operation.
The tool
offset
data
set
in
the
system
may
be
output
to
paper
tape
.
The
output
operation
is
as
follows
1.
c.
Power
on
the
NC.
Select
EDIT
mode.
Depress
the
RESET
key.
Depress
the
OFS
key.
Check
that
the
punch
is
ready
for
opera¬
tion
.
A
B.
C.
D.
—
22
—