The wire gauges listed in the following tables are Yaskawa recommendations. Refer to NEC table 310-16 for proper wire
gauge selection for terminals -M, +M, -1, +3, and ground.
Wire Gauges and Tightening Torques
Refer to Wire Gauges and Tightening Torque on page 23 to select the appropriate wires and crimp terminals for use in the
United States.
Closed-Loop Crimp Terminal Recommendations
Yaskawa recommends using closed-loop crimp terminals on all drive models. To maintain UL/cUL approval, UL Listed
closed-loop crimp terminals are specifically required when wiring the drive main circuit terminals on models 2A0031 to
2A0396 and 4A0034 to 4A0590. Use only the tools recommended by the terminal manufacturer for crimping. Yaskawa
recommends crimp terminals made by JST and Tokyo DIP (or equivalent) for the insulation cap.
Table i.34 matches the wire gauges and terminal screw sizes with Yaskawa-recommended crimp terminals, tools, and insulation
caps. Refer to the appropriate Wire Gauge and Torque Specifications table for the wire gauge and screw size for your drive
model. Place orders with a Yaskawa representative or the Yaskawa sales department. Refer to local codes for proper selections.
Table i.34 Closed-Loop Crimp Terminal Size
Wire Gauge
Terminal
Screws
Crimp Terminal
Model Number
Tool Insulation
Cap
Model No.
Code
<1>
Machine No. Die Jaw
2 mm
2
14 AWG
M4 R2-4 YA-4 AD-900 TP-003 100-054-028
3.5 / 5.5 mm
2
12 / 10 AWG
M4 5.5-4NS YA-4 AD-900 TP-005 100-064-248
8 mm
2
8 AWG
M4 8-4NS YA-4 AD-901 TP-008 100-064-249
M5 R8-5 YA-4 AD-901 TP-008 100-054-032
14 mm
2
6 AWG
M5 R14-5 YA-4 AD-902 TP-014 100-054-034
M8 R14-8 YA-5 AD-952 TP-014 100-054-035
22 mm
2
4 AWG
M5 22-5NS YA-5 AD-953 TP-022 100-051-262
M8 R22-8 YA-5 AD-953 TP-022 100-051-263
30 / 38 mm
2
3 / 2 AWG
M8 R38-8 YA-5 AD-954 TP-038 100-051-264
50 / 60 mm
2
1 AWG
1/0 AWG
1/0 AWG × 2P
M8 R60-8 YA-5 AD-955 TP-060 100-051-265
70 mm
2
2/0 AWG
2/0 AWG × 2P
M8
CB70-S8
YF-1 YET-300-1 TD-322,TD-311 TP-080
100-064-417
70-8 100-064-250
M10 70-10 YF-1 YET-300-1 TD-322,TD-311 TP-080 100-064-251
80 mm
2
3/0 AWG × 2P
3/0 AWG × 4P
M10 80-10 YF-1 YET-300-1 TD-323,TD-312 TP-080 100-051-267
M12 80-L12 YF-1 YET-300-1 TD-323,TD-312 TP-080 100-051-558
100 mm
2
4/0 AWG × 2P
4/0 AWG × 4P
M12 100-L12 YF-1 YET-300-1 TD-324,TD-312 TP-100 100-051-560
150 mm
2
250 kcmil × 2P
300 kcmil × 2P
M12 150-L12 YF-1 YET-300-1 TD-325,TD-313 TP-150 100-051-562
<1> Codes refer to a set of three crimp terminals and three insulation caps. Prepare input and output wiring using two sets for each connection.
Example 1: Models with 300 kcmil for both input and output require one set for input terminals and one set for output terminals, so the user should
order two sets of [100-051-272].
Example 2: Models with 4/0 AWG × 2P for both input and output require two sets for input terminals and two sets for output terminals, so the user
should order four sets of [100-051-560].
Note: Use crimp insulated terminals or insulated shrink tubing for wiring connections. Wires should have a continuous maximum allowable
temperature of 75 °C 600 Vac UL-approved vinyl-sheathed insulation.
i.9 Standards Compliance
84
YASKAWA ELECTRIC TOEP C710616 54A YASKAWA AC Drive - Z1000 Quick Start Guide
To Next Page
Loading...
