York YR - Chiller ID; Seiko; Weigh - Tronix Printer

JOHNSON CONTROLS
98
FORM 160.81-O1 (1020)
ISSUE DATE 10/05/2020
SECTION 4 - PRINTERS
Seiko
DipSW 1-1 = OFF Input-Serial
DipSW 1-2 = ON Printing Speed High
DipSW 1-3 = ON Auto Loading - ON
DipSW 1-4 = OFF Auto Lf - OFF
DipSW 1-5 = ON Setting Command - Enable
DipSW 1-6 = OFF Printing Density - 100%
DipSW 1-7 = ON Printing Density - 100%
DipSW 1-8 = ON Printing, Density - 100%
DipSW 2-1 ON Printing Columns - 40
DipSW 2-2 = ON User Font Back-Up - ON
DipSW 2-3 = ON Character Select - Normal
DipSW 2-4 = OFF Zero - Slash
DipSW 2-5 = ON
International Character Set -
American
DipSW 2-6 = ON
International Character Set -
American
DipSW 2-7 = ON
International Character Set -
American
DipSW 2-8 = OFF
International Character Set -
American
DipSW 3-1 = ON Data Length - 8 Bits
DipSW 3-2 = ON Parity Setting - No
DipSW 3-3 = ON Parity Condition - Odd
DipSW 3-4 = ON Busy Control - H/W Busy
DipSW 3-5 = ON Baud Rate Select - 1200*
DipSW 3-6 = OFF Baud Rate Select - 1200*
DipSW 3-7 = ON Baud Rate Select - 1200*
DipSW 3-8 = OFF Baud Rate Select - 1200*
* Settings shown for 1200 Baud. Other Baud rates can be se-
lected. Refer to Printer manufacturer’s manual supplied with
Printer.
CONTROL CENTER SETUP
Chiller ID
Access Level Required: OPERATOR
Using the COMMS screen, assign an Identification
number to the chiller. This number will appear at the
top of each report.
CONTROL BOARD SWITCH SETTINGS
SW1-8 ON SDD (-) Pin 11
SW2-1 ON 1200 Baud*
SW2-2 ON 1200 Baud*
SW2-3 OFF 1200 Baud*
SW2-4 OFF DSR Active
SW2-5 ON Bu󰀨er Threshold 32 Bytes
SW2-6 ON Busy Signal 200ms
SW2-7 ON DTR Space After Power ON
SW2-8 Not Used
If equipped with HIGH SPEED serial board:
CONTROL BOARD SWITCH SETTINGS
SW1 OFF (-) Low When Busy
SW2 OFF 1200 Baud*
SW3 OFF 1200 Baud*
SW4 ON 1200 Baud*
SW5 Not Used
SW6 OFF No Parity
SW7 OFF Pin 20 & Pin 11 Act As Busy Line
Weigh - Tronix Printer
IMP-24 MODEL 2600
SW1 - OFF 1200 Baud*
SW2 - ON 1200 Baud*
MODEL 1220
Congure Menu
Baud = 1200
Data Bits = 8
Stop Bits = 1
Hshake = Busy-Line
Cols = 32
Invert = No
Font = 5 X 8
Mag = None
Custom Menu
Auto Seq = No
Zero = 0
Pound Sign = #
_(Underscore)
Busy Invert = No
ONline/OFFline = Yes
Ext Ch Set = No
Print Ready = Yes
Set Clock = Not Used
Reset Seq = Not Used
(CONT'D)