ABB REF611 - Page 153

Master Trip 1
OSWGAPC2
Master Trip 2
Trip 1
Trip 2
Trip 3
Trip 4
T1PTTR1_ALARM
RDRE_TRIGGERED
TCSSCBR1_ALARM
TCSSCBR2_ALARM
CCBRBRF1_TRBU
CCBRBRF1_TRRET
DARREC1_INPRO
DARREC1_LOCKED
DARREC1_PROT_CRD
DARREC1_UNSUC_RECL
DARREC1_AR_ON
DARREC1_READY
SELGAPC1_OUT_9
TRPPTRC1_CL_LKOUT
TRPPTRC2_CL_LKOUT
OSWGAPC1
OSWGAPC3
OSWGAPC11
Alarm 1
TRPPTRC1
TRPPTRC2
SELGAPC4
DPHLPDOC1_OPERATE
DPHLPDOC2_OPERATE
DPHHPDOC1_OPERATE
PHIPTOC1_OPERATE
EFHPTOC1_OPERATE
DEFLPDEF1_OPERATE
DEFLPDEF2_OPERATE
DEFHPDEF1_OPERATE
ROVPTOV1_OPERATE
ROVPTOV2_OPERATE
ROVPTOV3_OPERATE
INTRPTEF1_OPERATE
NSPTOC1_OPERATE
NSPTOC2_OPERATE
PDNSPTOC1_OPERATE
T1PTTR1_OPERATE
CCBRBRF1_TRRET
CBPSOF1_OPERATE
DPHLPDOC1_START
DPHLPDOC2_START
DPHHPDOC1_START
PHIPTOC1_START
EFHPTOC1_START
DEFLPDEF1_START
DEFLPDEF2_START
DEFHPDEF1_START
ROVPTOV1_START
ROVPTOV2_START
ROVPTOV3_START
INTRPTEF1_START
NSPTOC1_START
NSPTOC2_START
PDNSPTOC1_START
T1PTTR1_START
DPHLPDOC1_OPERATE
DPHLPDOC2_OPERATE
DPHHPDOC1_OPERATE
PHIPTOC1_OPERATE
EFHPTOC1_OPERATE
DEFLPDEF1_OPERATE
DEFLPDEF2_OPERATE
DEFHPDEF1_OPERATE
ROVPTOV1_OPERATE
ROVPTOV2_OPERATE
ROVPTOV3_OPERATE
INTRPTEF1_OPERATE
NSPTOC1_OPERATE
NSPTOC2_OPERATE
PDNSPTOC1_OPERATE
T1PTTR1_OPERATE
OSWGAPC8
OSWGAPC7
OSWGAPC10
OSWGAPC9
Start 1
Start 2
OSWGAPC4
OSWGAPC5
Start 3
Start 4
OSWGAPC6
LED1
LED2
LED3
LED4
LED5
LED6
LED7
LED8
OSWGAPC12
Alarm 2
OSWGAPC13
Alarm 3
OSWGAPC14
Alarm 4
OSWGAPC15
Alarm 5
OSWGAPC16
Alarm 6
GUID-1F4CCBC9-4EAC-4E46-92DD-4A1DB0D5AACF V2 EN
Figure 129: LEDs
SELGAPC3
SELGAPC3 is used to configure the OSWGAPC outputs to the protection relay
binary outputs. Master trip signals are connected to SELGAPC3 via TRPPTRC. Start,
trip and alarm signals are connected to SELGAPC3 via TPGAPC. TPGAPC are
timers and used for setting the minimum pulse length for the outputs.
1MRS757456 D Section 3
REF611 standardized configurations
REF611 147
Application Manual