Why am I getting a High DC Bus Voltage Fault on my AC Tech DC Drives?
A high DC bus voltage fault in AC Tech DC Drives can occur due to several reasons: the line voltage might be too high, the deceleration rate might be too fast, or there could be an overhauling load. For fast deceleration or overhauling loads, dynamic braking may be required.
What to do if AC Tech DC Drives show Incompatibility Fault?
If you're encountering an Incompatibility Fault with your AC Tech DC Drives, it means an EPM with an incompatible parameter version has been installed. You can either remove the EPM or perform a factory reset using Parameter 48 to change the parameter version of the EPM to match that of the drive.
How to resolve Control Fault on AC Tech DC Drives?
A Control Fault in AC Tech DC Drives means that a blank EPM or an EPM with corrupted data has been installed. To resolve this, perform a factory reset using Parameter 48 - PROGRAM SELECTION.
What does External Fault mean on AC Tech SM220S DC Drives?
An External Fault in AC Tech DC Drives is triggered when one of the TB-13 terminals is set as an External Fault input and that terminal is open with respect to TB-11. Refer to Parameters 10, 11, and 12.
Why AC Tech SM220S DC Drives show Start Fault?
A Start Fault in AC Tech DC Drives occurs when a start command was present when the drive was powered up. If START METHOD is set to NORMAL, you must wait 2 seconds after power-up to apply the Start command.
What causes Low DC Bus Voltage Fault in AC Tech SM220S?
A Low DC Bus Voltage Fault in AC Tech DC Drives indicates that the line voltage is too low.
What does Dynamic Braking Fault mean in AC Tech SM220S DC Drives?
A Dynamic Braking Fault in AC Tech DC Drives means that the drive has detected that the dynamic braking resistors are overheating.
What does Data Fault mean in AC Tech DC Drives?
A Data Fault in AC Tech DC Drives means that user data and OEM defaults in the EPM are corrupted.
Covers defects in material and workmanship for 24 months from shipment date.
Warns of electrical hazards and need for qualified personnel.
Guidelines for electrical installation, safety regulations, and codes.
Specifies that the drive is not a safety device and must not be used for critical safety functions.
Warning about electrical shock due to stored charge in capacitors.
Details input voltage ranges for SM000S, SM200S, SL200S, SM200, and SM400 series.
Warns about DC current in protective conductor and RCD type requirements.
Instructions for wiring input power and output motor connections.
Caution against connecting AC to output terminals or B+/B- and leakage current.
Explains analog speed reference inputs like speed pots, 0-10 VDC, and 4-20 mA.
Details how to select speed references via terminals and parameters.
Critical warning about JOG mode and STOP signal behavior.
Instructions for RUN/STOP, reverse direction, and speed source setup.
Guides on programming for start/stop, reverse, and speed source.
Instructions for programming preset speeds and speed pot control.
Electrical shock hazard warning due to charged capacitors.
Warnings against incorrect output connections and rapid power cycling.
Describes the EPM's function, removability, and use for quick setup.
Calibrates drive for applied input voltage (HIGH/LOW).
Sets switching rate for motor noise reduction.
Defines how the drive starts (e.g., normal, on power up).
Warns about automatic starting causing injury or damage.
Defines stop methods: Coast, Coast with DC Brake, Ramp, Ramp with DC Brake.
Selects speed reference source when in STANDARD speed mode.
Selects function for terminal TB-13A.
Selects function for terminal TB-13B.
Selects input or output functions for terminal TB-13E.
Selects source for START/STOP and direction commands.
Sets rotation direction (forward only or both).
Sets acceleration rate from 0 Hz to BASE FREQUENCY.
Selects user/OEM settings and resets parameters to defaults.
Lists fault codes, their descriptions, and possible causes.
General| Model | SM220S |
|---|---|
| Category | DC Drives |
| Frequency | 50/60 Hz |
| Input Voltage | 115/230V AC |
| Output Voltage | 0-180V DC |
| Operating Temperature | 0°C to 40°C |
| Storage Temperature | -20°C to 60°C |
| Protection Features | Overcurrent, Overtemperature, Short Circuit |
To Next Page
