Why is my Acer Projector image flickering?
If the image from your Acer Projector is unstable or flickering, try adjusting the "Tracking" settings. You can find more information about this in the "Image" section. If that doesn't resolve the issue, try changing the display color depth settings on your computer.
How to adjust Acer Projector image size?
If the image displayed by your Acer Projector is too small or too large, try adjusting the zoom ring on the projector. You can also move the projector closer to or further from the screen. Additionally, you can press "MENU" on the remote, navigate to "Image -> Aspect Ratio", and experiment with different settings, or press "RATIO" on the remote to adjust directly.
How to fix no image on Acer Projector?
First, ensure that all connections are properly set up as described in the "Getting Started" section. Then, check the connector pins for any damage. Confirm that the projector lamp is securely installed, referencing the "Replacing the Lamp" section if needed. Finally, remove the lens cap and ensure the projector is switched on.
Why is my Acer Projector not displaying from my notebook?
If you are using a Microsoft® Windows® based notebook, some notebook PCs may deactivate their own screens when a second display device is in use. Refer to your computer's manual for detailed information on how to reactivate it. If you are using an Apple® Mac® OS based notebook, open Display in System Preferences and select Video Mirroring "On".
How to fix slanted sides on Acer Projector image?
If your Acer Projector image has slanted sides, try these solutions. If possible, reposition the projector so it is centered on the screen. Alternatively, press the "Keystone / " button on the remote control until the sides appear vertical.
Why does Acer Projector lamp burn out?
When the lamp in your Acer Projector reaches the end of its life, it will burn out and may make a loud popping sound. If this occurs, the projector will not turn on until the lamp module is replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section.
Why does my Acer Projector lamp burn out or pop?
When the lamp reaches the end of its useful life, it will burn out and may make a loud popping sound. If this occurs, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section.
Why is my Acer Projector image out of focus?
To correct an out-of-focus image on your Acer Projector: * Ensure that the lens cap is removed. * Adjust the focus ring on the projector lens. * Make sure the projection screen is within the required distance of 3.3 to 29.7 feet (1.0 to 9.1 meters) for XGA series / 3.3 to 25.2 feet (1.0 to 7.7 meters) for WXGA series / 3.3 to 24.6 feet (1.0 to 7.5 meters) for 1080p series / 3.3 to 24.0 feet (1.0 to 7.3 meters) for WUXGA series from the projector.
How to fix a partial or scrolling image on Acer N368?
For an incorrectly displayed image: Open "My Computer", then the "Control Panel", and double-click the "Display" icon. Select the "Settings" tab. Verify that your display resolution setting is lower than or equal to WUXGA-RB (1920 x 1200). Click the "Advanced Properties" button. If the problem persists, change the monitor display you are using and follow these steps: Verify that the resolution setting is lower than or equal to WUXGA-RB (1920 x 1200). Click the "Change" button under the "Monitor" tab. Click "Show all devices". Next, select "Standard monitor types" under the SP box, and choose the resolution mode you need under the "Models" box. Verify that the resolution setting of the monitor display is lower than or equal to WUXGA-RB (1920 x 1200).
How to fix out of focus image on Acer N368?
First, ensure that the lens cap is removed. Then, adjust the focus ring on the projector lens. Also, make sure the projection screen is within the required distance: 3.3 to 29.7 feet (1.0 to 9.1 meters) for XGA series, 3.3 to 25.2 feet (1.0 to 7.7 meters) for WXGA series, 3.3 to 24.6 feet (1.0 to 7.5 meters) for 1080p series, or 3.3 to 24.0 feet (1.0 to 7.3 meters) for WUXGA series. You can find more information in the "How to get a preferred image size by adjusting distance and zoom" section.
To Next Page
General
