Acer PL6610T User Manual

English
33
USING THE PROJECTOR
Brightness Mode
Adjust the brightness mode settings.
 DynamicBlack: Use to automatically adjust the picture brightness in order to give optimum contrast
performance.
 Power: Choose the power percentage for brightness mode.
Reset
Return the factory default settings for color settings.
Display 3D menu
Note:
 This projector is a 3D ready projector with DLP-Link 3D solution.
 Please make sure your 3D glasses are use for DLP-Link 3D before enjoy your video.
 This projector supports frame sequential (page-ip) 3D via HDMI/VGA ports.
 To enable 3D mode, the input frame rate should be set to 60Hz only, lower or higher frame rate is not
supported.
 To reach the best performance, resolution 1920x1080 is recommended, please be noted that 4K
(3840x2160) resolution is not supported in 3D mode.
3D Mode
Use this option to disable the 3D function or select the appropriate the 3D function.
 O󰀨: Select “O󰀨” to turn o󰀨 3D mode.
 DLP-Link: Select to use optimized settings for DLP 3D Glasses.
Note: If the 2D and 3D sources enter PJ at the same time, if the ghosting image appears in the 2D source, make
sure to manually turn o the 3D function.
3D → 2D
Use this option to specify how the 3D content should appear on the screen.
 3D: Display 3D signal.
 L (Left): Display the left frame of 3D content.
 R (Right): Display the right frame of 3D content.
3D Format
Use this option to select the appropriate 3D format content.
 Auto: When a 3D identication signal is detected, the 3D format is selected automatically.
 SBS: Display 3D signal in “Side-by-Side” format.
 Top and Bottom: Display 3D signal in “Top and Bottom” format.
 Frame Sequential: Display 3D signal in “Frame Sequential” format.
3D Sync Invert
Use this option to enable/disable the 3D sync invert function.

Acer PL6610T Specifications

General

Number of colors	1.073 billion colors
Native aspect ratio	16:10
Projection distance	1 - 9 m
Projection technology	DLP
Supported aspect ratios	4:3, 16:10, 16:9
Contrast ratio (typical)	2000000:1
Screen size compatibility	- \
Projector native resolution	WUXGA (1920x1200)
Vertical synchronization (max)	0.12 kHz
Vertical synchronization (min)	0.023 kHz
Keystone correction, horizontal	-30 - 30 °
Horizontal synchronization (max)	102 kHz
Horizontal synchronization (min)	15 kHz
Lamps quantity	1 lamp(s)
Light source type	Laser
Service life of light source	20000 h
Service life of light source (economic mode)	30000 h
Built-in display	No
Focus	-
Throw ratio	1.4 to 2.24 (1676.40 mm@2000 mm)
Zoom capability	Yes
Focal length range	20.91 - 32.62 mm
Aperture range (F-F)	2.5 - 3.26
Analog signal format system	NTSC, PAL, SECAM
Composite video in	1
Serial interface type	RJ-45
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
VGA (D-Sub) ports quantity	3
Component video (YPbPr/YCbCr) in	0
Noise level	- dB
Projection modes	Ceiling, Front, Rear
Compatible operating systems	Mac Windows
RMS rated power	10 W
Placement	Ceiling
Product type	Ceiling-mounted projector
Product color	White
Cable lock slot type	Kensington
Power source	AC
AC input voltage	120 - 230 V
Power consumption (standby)	- W
Power consumption (typical)	321 W
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	0 - 80 %
Harmonized System (HS) code	85286200

Weight and Dimensions

Weight	6000 g