22
Appendix D Specifications
Inputs: Analog Line Connectors:
1 single-ended RCA and 1 Balanced XLR for each of the 5 analog Line Inputs.
Input Impedance: 20K Single-ended or 40K Balanced (20K per phase).
Gain: (Tube variable) Preamp: 24dB maximum w/gain jumpers @ 0dB.
Power amp: 26dB.
Polarity: (Balanced) Pin-2 = Positive, Pin-3 = Negative.
Phono (optional):
1 balanced XLR and 1 single-ended RCA per channel for the Phono input 1.
1 single-ended RCA per channel for the Phono input 2.
Resistive & capacitance Load as well as Gain control. Ranges variable when MC or MM is selected.
Fully discrete FET-based, high gain differential circuit.
Digital (Optional):
2 x RCA, 2 x TosLink, 1 x USB 24bit / 352K, DSD & DSD2. USB utilizes Wavelength Technologies'
asynchronous implementation.
Outputs: Speaker:
Connectors: 1 balanced bridge output per channel. (See Power Output below).
Impedance: 0.25 ohms @ 1KHz.
Preamp Out:
Connectors: 1 balanced and 1 single-ended per channel.
Headphone: ¼” standard headphone stereo jack. 1/3W into 32 ohms, IC based.
HD (Optional): 1W into 32 ohms, fully discrete Class A with Mogami wiring.
Modes/Processes: Standby; Auto sense headphone & trigger; Home Theater Bypass (hardware & software) available to
each analog line input; Individual analog input level control; Internal Hi/Lo gain jumpers; Optional
adjustable high pass filter installable on Output modules.
Volume Control: 88 1dB steps, utilizing individual switched 1% metal film resistors.
Tubes (2) - One 6922 (6DJ8) or equivalent per channel.
Crossover: (Optional) High pass 60Hz, 80Hz, 100Hz or 120Hz, hardware adjustable. All slopes are 6dB.
Power Output: (8 ohms) 150 W (rated) 185 W (typical).
(4 ohms) Nearly double.
Frequency Response:(-3dB points @ full power) 4 - 150 kHz.
THD+Noise: <1.0% (both channels driven at 150W into 8 ohms).
Control: RS232: 1 DB9 connector.
IR extender 1/8" stereo jack.
Trigger: 1/8” Jack, +5 and +12V auto sense Level or Pulse (> 100mS: Level; <100mS: Pulse).
Power Consumption: Active (no signal): 210W; Standby (normal mode): 100W; Standby (high efficiency mode): 6W.
Dimensions: 17 7/8” W x 17" 11/16” D x 7 1/2” H (43.4 x 44.9 x 14 cm).
Boxed: 22” x 22” x 10” (55.8 x 55.8 x 25.4 cm).
Weight: 42 Lbs. Standalone (19.1 Kg), 51 Lbs boxed with accessories (23.1 Kg).
Maximum Operating Internal: 176 F (80 C).
Temperature: Room: 122 F (50 C).
Fuses: (All 5 x 20mm) Mains: 10A SB @100, 117VAC. 5A SB @230, 245VAC.
Relay board: 1/2A SB @100, 117V AC. 1/4A SB @230, 245VAC.
Audio Outputs: 10A FB.
Specifications subject to improvement or change without notice.
To Next Page
Loading...