Agilent Technologies N5182A Installation Guide

40 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Agilent Technologies

Agilent Technologies

N5161A/62A/81A/82A/83A

MXG Signal Generators

Installation Guide

Notice: This document contains references to

Agilent. Please note that Agilent’s Test and

Measurement business has become Keysight

Technologies. For more information, go to

www.keysight.com.

Table of Contents

Other manuals for Agilent Technologies N5182A

User Guide175 pages

Programming Guide366 pages

Service Guide202 pages

Questions and Answers:

A
alexandra11Aug 21, 2025
What to do if Agilent Technologies N5182A Portable Generator has no RF output?
- M
  Michael VelazquezAug 21, 2025
  If your Agilent Technologies Portable Generator has no RF output, there are several things to check: * First, check the RF ON/OFF LED. If it's off, press the RF On/Off button to turn the output on. * Next, make sure that the amplitude is set within the signal generator’s specified range. * If the instrument is playing a waveform, verify that the marker polarity and routing settings are correct.
M
Michael SmithAug 23, 2025
Why is the RF output power too low on my Agilent Technologies N5182A?
- J
  Justin CooperAug 23, 2025
  There are several reasons why the RF output power might be too low on your Agilent Technologies Portable Generator: * If the AMPLITUDE area of the display shows the OFFS indicator, eliminate the offset by pressing **Amptd > More (1 of 2) > Amptd Offset > 0 > dB**. * If the AMPLITUDE area of the display shows the REF indicator, turn off the reference mode by pressing **Amptd > More > Amptd Ref Off On** until Off highlights. Then, reset the output power to the desired level. * If pulse modulation is on, turn off the ALC, and check that pulse width is within specifications.
J
John PearsonAug 25, 2025
What to do if Agilent Technologies N5182A power supply shuts down?
- M
  Maria CollinsAug 25, 2025
  If the power supply of your Agilent Technologies Portable Generator isn't working, it likely requires repair or replacement. If you cannot service it yourself, send the signal generator to an Agilent service center.
J
jacksonjamesAug 26, 2025
What to do if there is no modulation at the RF output of my Agilent Technologies N5182A Portable Generator?
- J
  Jason SanchezAug 27, 2025
  If there is no modulation at the RF output, try the following: * Check both the Mod On/Off LED and the Off On softkey, and ensure that both are on. * If you're using a vector signal generator with digital modulation, make sure that the internal I/Q modulator is on (the I/Q annunciator should be displayed). * If you're using an external modulation source, verify that the external source is on and operating within the signal generator’s specified limits.
S
Sean MejiaAug 27, 2025
How to turn off sweep on Agilent Technologies Portable Generator?
- S
  Shari WuAug 27, 2025
  To turn off the sweep function on your Agilent Technologies Portable Generator, press **Sweep > Sweep > Off**.
D
Daniel BurgessAug 30, 2025
Why is there distortion in the output signal of my Agilent Technologies Portable Generator?
- T
  Troy CollinsAug 31, 2025
  If you edit and resave a segment in a waveform sequence, the sequence does not automatically update the RMS value stored in its header. To resolve distortion, display the sequence header information and recalculate the RMS value.
J
Jerry ProctorSep 1, 2025
What causes signal loss while working with a spectrum analyzer and Agilent Technologies N5182A?
- Y
  yvette63Sep 1, 2025
  The effects of reverse power can cause problems with the RF output when you use the Agilent Technologies Portable Generator with a spectrum analyzer that does not have preselection. Use an unleveled operating mode to resolve this.
W
williamsaprilSep 3, 2025
What causes signal loss while working with a mixer and Agilent Technologies Portable Generator?
- H
  Haley DiazSep 3, 2025
  To fix signal loss at the signal generator’s RF output during low-amplitude coupled operation with a mixer, add attenuation and increase the RF output amplitude.
K
kennethespinozaSep 4, 2025
Why is the list sweep information missing from a recalled register on my Agilent Technologies Portable Generator?
- M
  Miranda NicholsonSep 4, 2025
  List sweep information is not stored as part of the instrument state in an instrument state register. Only the current list sweep is available to the signal generator. You can store list sweep data in the instrument catalog.
M
madisonjeffersonSep 6, 2025
Why is the instrument state saved, but the register is empty or contains the wrong state on my Agilent Technologies Portable Generator?
- R
  Robert SmithSep 6, 2025
  If the register number you intended to use is empty or contains the wrong instrument state, recall register 99. If you selected a register number greater than 99, the signal generator automatically saves.

Agilent Technologies N5182A Specifications

General

Amplitude Accuracy	±0.5 dB
I/Q Modulation	Yes
Interface	LAN, USB, GPIB
Modulation Types	AM, FM, PM, Pulse
Sweep Types	List
Connectivity	LAN, USB, GPIB
Power Requirements	100-240 VAC, 50/60 Hz
Phase Noise	-115 dBc/Hz at 1 GHz, 20 kHz offset

Related product manuals

Preview: Agilent Technologies n5181a

Agilent Technologies n5181a

Agilent Technologies N5183A

Preview: Agilent Technologies N5161A

Agilent Technologies N5161A

Agilent Technologies E8267C

Agilent Technologies E4421B

Agilent Technologies E4422B

Agilent Technologies E4431B

Agilent Technologies E4432B

Agilent Technologies E4437B

Agilent Technologies E4433B

Preview: Agilent Technologies E4423B

Agilent Technologies E4423B

Preview: Agilent Technologies X Series

Agilent Technologies X Series