AL-KO Robolinho 1150 User Manual (English)

Other manuals for AL-KO Robolinho 1150

Manual652 pages

Original Instructions For Use504 pages

Questions and Answers:

A
Ashley AndersonSep 7, 2025
What to do if my AL-KO Robolinho 1150 battery is not working?
- R
  Ricky NelsonSep 7, 2025
  There could be several reasons why your AL-KO Lawn Mower battery isn't working: * The rechargeable battery may be flat. * There may be no contact to the charging contacts during charging. * Obstacles might be close to the base station. * The appliance may be stuck. * The appliance may not be finding the base station. To address these issues: * Ensure the boundary cable location is correct. * Clean the charging contacts. * Place the appliance in the base station, ensuring the charging contacts make contact. * Remove any obstacles. * Place the appliance on the designated grass surface.
D
Diana AdamsAug 23, 2025
What to do if AL-KO Robolinho 1150 Lawn Mower bumper deflected?
- M
  Michelle ClarkAug 23, 2025
  If the AL-KO Lawn Mower has driven into an obstacle and cannot free itself, especially near the base station, place the appliance on the designated grass surface. Also, ensure the boundary cable is correctly positioned.
L
Laura SmithAug 25, 2025
Why does my AL-KO Lawn Mower say no loop signal?
- D
  David HintonAug 26, 2025
  If your AL-KO Lawn Mower displays a 'No loop signal' error, first check the LEDs on the base station. Then, check the power source by disconnecting and reconnecting it. Finally, inspect the boundary cable for any damage and repair it if necessary.
R
Richard KingAug 26, 2025
Why is the loop signal weak on my AL-KO Robolinho 1150?
- J
  jorge62Aug 26, 2025
  If your AL-KO Lawn Mower shows a weak loop signal, check the LEDs on the base station and ensure the power source is properly connected by disconnecting and reconnecting it. If the issue persists, raise the boundary cable to the correct height, attaching it directly to the grass if needed. It might be that the boundary cable is buried too deep.
D
Duane FoxAug 27, 2025
What to do if AL-KO Robolinho 1150 is in bad position?
- D
  Daniel MckeeAug 27, 2025
  If your AL-KO Lawn Mower is in a bad position, ensure it is placed on the designated grass surface. Correct the boundary cable's location around curves and obstacles, and eliminate any criss-crossing of the cable. This may happen because the appliance is outside the designated grass surface or the boundary cable has been routed in a criss-cross pattern.
T
timothy21Aug 28, 2025
How to fix AL-KO Robolinho 1150 escaped robot error?
- M
  marshallmaryAug 29, 2025
  If the AL-KO Lawn Mower has escaped, correct the location of the boundary cable around curves and obstacles, as the appliance is outside the designated grass surface.
J
Janet AndersonSep 13, 2025
What to do if my AL-KO Lawn Mower 'escaped'?
- T
  Timothy DelgadoSep 13, 2025
  If your AL-KO Lawn Mower displays an 'escaped robot' error, it means the appliance is outside the designated grass surface. Correct the location of the boundary cable around curves and obstacles to prevent this.
M
Mary CallahanSep 9, 2025
What to do if my AL-KO Lawn Mower is in a bad position?
- R
  Ronald HansonSep 9, 2025
  If your AL-KO Lawn Mower shows a 'bad position' error, it means the appliance is outside the designated grass surface or the boundary cable has been routed in a criss-cross pattern. To fix this, place the appliance on the free, designated grass surface and correct the location of the boundary cable around curves and obstacles, eliminating any criss-crossing of the cable.
J
Jessica ArmstrongSep 6, 2025
What to do if my AL-KO Lawn Mower has no loop signal?
- M
  Melissa CookSep 6, 2025
  If your AL-KO Lawn Mower displays a 'no loop signal' error, the boundary cable might be faulty, or the loop signal might be too weak. You can try to check the LEDs on the base station, check the power source of the base station by disconnecting and reconnecting the power supply, and inspect the boundary cable for any damage. If you find any damage, repair the defective cable.
V
valentinerichardSep 3, 2025
How to fix AL-KO Lawn Mower tilt sensor error?
- K
  Kevin RodriguezSep 3, 2025
  If the AL-KO Lawn Mower's tilt sensor is triggered, place the appliance on a flat surface and acknowledge the fault. This may occur if the maximum tilt is exceeded, the appliance has been carried, or the slope is too steep.

AL-KO Robolinho 1150 Specifications

General

Type	Robotic lawn mower
Cutting width	220 mm
Grass catcher	No
Product color	Gray
Number of blades	4
Number of wheels	4 wheel(s)
Rotational speed	3400 RPM
Maximum lawn area	1200 m²
Mulching function	-
Sound power level	58 dB
Sound pressure level	60 dB
Maximum cutting height	55 mm
Minimum cutting height	25 mm
Cutting clearance adjustment	Yes
International Protection (IP) code	IPX1
Power source	Battery
Battery voltage	25 V
Battery capacity	5 Ah
Battery life (min)	100 min