Operating Instructions
Part No. 70458301ENR7
©
Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 119
• RPM display – when equipped with rotational sensor only
• Monitors the lint door switch operation
• Monitors the thermistor for operation
The minimum drying time is 0 minutes, and the minimum
cooling time is 2 minutes. The maximum drying or cooling time
is 60 minutes. The drying temperature may be set from 100ºF
(38ºC) to 185º/195ºF (85º/91ºC). The drying time, cooling time,
or temperature may be modified during an operating cycle.
If it is necessary to reset the drying and cooling times for the
current cycle, press STOP once to stop the tumble dryer. Press
STOP again to cancel the cycle.
If it is necessary to change programs during a current cycle,
press STOP once to stop the tumble dryer and press STOP again
to cancel the current cycle.
Programming
1. Set DIP switch #8 to the ON position.
2. Select the desired program number to change. The LED
should be flashing.
3. Select DRY TIME. Set the time with the Up/Down arrows.
4. Select COOL TIME. Set the time with the Up/Down
arrows.
5. Select TEMPERATURE. Set the temperature with the Up/
Down arrows.
6. Select reversing REV (illuminated) or nonreversing REV
(not illuminated). To change basket direction and dwell
time, see Reversing Operation.
7. Press and hold the Program Select button about 3 seconds
until the LED stops flashing. The selected program number
is now programmed. If the Program button is pressed for
less than 3 seconds, the controller will cancel the program
and display the next program’s settings. If not programmed
correctly, the display will flash “E2F” for 4 seconds, and
the default settings will be used. Follow steps 4 through 7
to reprogram any program number. When finished, set DIP
switch #8 to OFF. The programs are now stored.
8. During the Program Mode, if the Up/Down arrows, REV, or
Display button is not pressed within 10 seconds, the default
program settings will be used.
9. Temporary Reprogramming of Current Programs (OPL
ONLY).
10. The Drying Time, Cooling Time, Temperature, and
Reversing Mode of a program currently in use may be
modified simply by adjusting any or all of the program
parameters for that program, as needed. Once a modification
has been made, the current program LED will flash
indicating that it has been modified.
11. Use the Up/Down arrows to adjust program time.
12. Use the Display Select button to choose between Drying
Time, Cooling Time, and Temperature. Then use the Up/
Down arrows to adjust the times and temperature.
13. Toggle between reversing REV (illuminated) or
nonreversing REV (not illuminated). (Only for tumble
dryers with the reversing option.)
14. To cancel this temporary programming mode push the
STOP button once to stop the current cycle and once more
to cancel the modified program settings. The program will
revert back to its original settings.
Reversing Operation
1. When the LOCAL reversing operation is selected, the
reversing times are stored in the EEPROM which is located
on the controller board. If the values stored are determined
to be invalid, the clockwise and counterclockwise times will
default to 60 seconds, and the dwell time will default to 4
seconds.
2. The reversing time program has the following sequence:
(1) clockwise time, (2) dwell time and (3) counterclockwise
time.
3. To program new reversing times DIP switches #3 and #8
must be on.
4. Press and hold the reverse button (REV) for 3 seconds to
display the clockwise time.
5. Use the Up/Down arrows to set the clockwise time within
the range of 30-120 seconds.
6. Press REV to display the dwell time.
7. Use the Up/Down arrows to change the dwell time within
the range of 3-10 seconds.
8. Press the REV button to display the counterclockwise time.
9. Use the Up/Down arrows to change the counterclockwise
time within the range of 30-120 seconds.
10. Press the REV button to save these settings and leave DIP
switch #3 in the ON position and flip DIP switch #8 to the
OFF position.
When the DMP controller is retrofitted to an existing tumble
dryer with the reversing feature, off board reversing will be
required and DIP switch #3 on the DMP must be in the OFF
position and the DMP must be connected to the Reversing Timer
Board for proper operation. The DMP settings for clockwise,
dwell, and counterclockwise times are no longer valid when
used with the Reversing Board. Instead these settings are made
on the Reversing Timer Board.
Rotation Sensor
The rotation sensor must “read” the key on the basket shaft or
pulley. The sensor must be set approximately 1/4 inch from the
key or pulley. Look for the light on the sensor to come on as
the key passes the sensor; this is a correctly operating sensor.
If no light appears, either the sensor is out of range or the key/
pulley or the sensor is bad. In addition, if the light stays on
continuously, then the sensor is too close to the component or
the sensor is bad.
To Next Page
Loading...
