Need help?Do you have a question about the Allied Telesis AT-S63 and is the answer not in the manual?
General| Vendor | Allied Telesis |
|---|---|
| Name | AT-S63 |
| Category | Software |
| Type | Network Management Software |
| Compatibility | Allied Telesis devices |
| Functionality | Network monitoring, configuration, and management |
Saves current configuration changes to the active boot configuration file.
Performs a soft reset on all ports, clears MAC addresses, and resets statistics.
Deletes the switch's name, contact, and location settings.
Resets the switch, running diagnostics and loading management software.
Loads a specified configuration file or resets parameters to default values.
Configures IP address and subnet mask parameters for the switch.
Specifies the IP address of the default gateway for the switch.
Sets the switch's name, administrator contact, and location.
Starts a management session on another switch in an enhanced stack.
Sets the switch's enhanced stacking status to master, slave, or unavailable.
Displays a list of switches participating in an enhanced stack.
Configures various operating parameters for switch ports like speed and status.
Sets the maximum number of ingress packets accepted per second on switch ports.
Adds static unicast and multicast MAC addresses to the switch's MAC address table.
Adds ports to an existing port trunk.
Creates a port trunk, specifying ports and load distribution method.
Enables or disables port mirroring and specifies the destination port.
Specifies source ports for port mirroring and the type of traffic to mirror.
Creates a new configuration file with commands to recreate the current switch configuration.
Sets the active configuration file for the switch's next reboot or power cycle.
Downloads software images, configuration files, or encryption keys onto the switch.
Uploads files such as software images or configurations from the switch to a management station or TFTP server.
Saves current event log entries to a file in the file system.
Maps Class of Service (CoS) priorities to port egress queues.
Maps CoS priorities to port egress queues, equivalent to MAP QOS COSP.
Sets the QoS scheduling method and weights for round robin scheduling.
Configures IGMP snooping parameters like status, host topology, and timeout.
Designates STP as the active spanning tree protocol on the switch.
Sets STP parameters like bridge priority, hello time, and forward delay.
Configures STP parameter settings for a switch port, including cost and priority.
Designates RSTP as the active spanning tree protocol on the switch.
Configures RSTP parameters such as bridge priority, hello time, and forwarding delay.
Sets a port's RSTP settings, including port cost, priority, and edge port status.
Designates MSTP as the active spanning tree protocol on the switch.
Associates VLANs with a Multiple Spanning Tree Instance (MSTI).
Creates a new MSTI ID and associates VLANs to the spanning tree instance.
Configures MSTP parameters such as force version, hello time, and max hops.
Sets the CIST priority number on the switch, used for root bridge determination.
Changes the MSTI priority value for a spanning tree instance.
Associates VLANs with specific spanning tree instances (MSTIs).
Sets a port's MSTP settings, including internal/external port costs and priority.
Creates an SNMPv3 User Table entry with authentication and privacy settings.
Creates an SNMPv3 Access Table entry, defining security groups and their properties.
Creates an SNMPv3 Community Table entry, defining community names and associated users.
Creates an SNMPv3 SecurityToGroup Table entry, linking users to groups.
Creates an SNMPv3 Notify Table entry, defining trap or inform messages.
Creates an SNMPv3 Target Address Table entry, specifying target hosts and parameters.
Creates an SNMPv3 Target Parameters Table entry, defining message processing and security levels.
Creates an SNMPv3 View Table entry, defining MIB access permissions.
Modifies an SNMPv3 Access Table entry, changing security models and views.
Modifies an SNMPv3 Community Table entry, updating passwords and transport tags.
Modifies an SNMPv3 SecurityToGroup Table entry, associating users with groups.
Modifies an SNMPv3 Notify Table entry, updating trap messages and types.
Modifies an SNMPv3 Target Address Table entry, updating host details and tags.
Modifies an SNMPv3 Target Parameters Table entry, adjusting message processing and security levels.
Modifies an SNMPv3 User Table entry, updating authentication and privacy settings.
Modifies an SNMPv3 View Table entry, changing subtree access permissions.
Adds tagged and untagged ports to an existing port-based or tagged VLAN.
Creates a new port-based or tagged VLAN, assigning a name and VID.
Sets the management VLAN used for Telnet and web browser management sessions.
Configures the switch for multiple VLAN modes or for creating port-based/tagged VLANs.
Adds ports to groups within a protected ports VLAN or specifies an uplink port.
Creates a new protected ports VLAN by assigning a name and VID.
Changes the security intrusion action on a port (discard, trap, or disable).
Sets the port's security mode to automatic, limited, secured, or locked.
Adds an access control entry (ACE) to the Management ACL, allowing remote management.
Configures the web server for secure HTTPS or non-secure HTTP operation.
Creates encryption key pairs or imports/exports public keys from the file system.
Creates a self-signed certificate using an encryption key pair.
Creates a certificate enrollment request for a public or private CA.
Selects the active authentication protocol (TACACS+ or RADIUS) and configures global keys and timeouts.
Sets ports to the Authenticator role and configures its parameters for 802.1x access control.
Sets ports to the Supplicant role and configures its parameters for 802.1x access control.
Activates and configures RADIUS accounting settings, including trigger and update intervals.
Configures IP address and subnet mask for SMURF and Land DoS defenses.
Enables or disables the IP Option DoS defense on specified ports.
Enables or disables the Land DoS defense on specified ports.
Activates or deactivates the Ping of Death DoS defense on specified ports.
Activates or deactivates the SMURF DoS defense on specified ports.
Activates or deactivates the SYN ACK Flood DoS defense on specified ports.
Activates or deactivates the Teardrop DoS defense on specified ports.
To Next Page
