Need help?Do you have a question about the Allied Telesis AT-8000S and is the answer not in the manual?
General| Category | Network Management Software |
|---|---|
| Compatible Devices | Allied Telesis switches and routers |
| Functionality | Network monitoring |
| User Interface | Graphical User Interface (GUI) |
| Protocols Supported | SNMP, Telnet, SSH |
Describes how to start using the CLI and the CLI command editing features.
Explains the different command modes within the Command Line Interface.
Describes the commands available in User EXEC mode for basic tests and system information.
Grants access to restricted commands and the device Configuration mode.
Manages the device configuration on a global level.
Modifies specific interface operations and configures various interface types.
Details the steps required to connect to and start using the CLI.
Defines an IPv4 Access List and enters IPv4 Access List Configuration mode.
Sets conditions to allow a packet to pass a named IP Access List.
Sets conditions to not allow a packet to pass a named IP Access List.
Defines an IPv6 Access List and enters IPv6 Access List Configuration mode.
Sets conditions to allow a packet to pass a named IPv6 Access List.
Sets conditions to not allow a packet to pass a named IPv6 Access List.
Defines a Layer 2 Access List and enters MAC-Access List Configuration mode.
Sets permit conditions for a MAC-Access List.
Sets deny conditions for a MAC-Access List.
Defines login authentication methods for user login.
Defines authentication method lists for accessing higher privilege levels.
Specifies the login authentication method for remote telnet or console.
Specifies authentication method for accessing higher privilege levels.
Specifies a password on a line.
Creates a user account in the local database.
Sets a local password to control access to user and privilege levels.
Adds a MAC-layer station source address to the bridge table.
Registers MAC-layer Multicast addresses to the bridge table.
Enables port security on an interface.
Configures the port security mode.
Configures the maximum number of addresses learned on a port.
Adds a MAC-layer secure address to a routed port.
Manually sets the system clock.
Configures an external time source for the system clock.
Configures the device to accept SNTP traffic from a specified server.
Copies files from a source to a destination.
Deletes a file from a flash memory device.
Specifies the system image that the device loads at startup.
Displays the contents of the currently running configuration file.
Displays the contents of the startup configuration file.
Globally enables DHCP snooping.
Enables DHCP snooping on a VLAN.
Configures a port as trusted for DHCP snooping purposes.
Configures the DHCP snooping binding file.
Configures the DHCP snooping binding database and adds binding entries.
Enters interface configuration mode to configure an Ethernet type interface.
Configures multiple Ethernet type interfaces simultaneously.
Disables an interface.
Configures the speed of a given Ethernet interface.
Configures the full/half duplex operation of an Ethernet interface.
Enables auto-negotiation operation for speed and duplex parameters of an interface.
Enables Broadcast storm control.
Configures the maximum Broadcast rate.
Enables the GARP VLAN Registration Protocol (GVRP) globally.
Enables GVRP on an interface.
Enables Internet Group Management Protocol (IGMP) snooping globally.
Enables IGMP snooping on a specific VLAN.
Enables automatic learning of Multicast device ports on a specific VLAN.
Enables Internet Group Management Protocol (IGMP) querier on a specific VLAN.
Defines the source IP address that the IGMP Snooping querier uses.
Sets an IP address on an interface.
Acquires an IP address for an interface from a DHCP server.
Defines a default gateway (device).
Adds a permanent entry in the Address Resolution Protocol (ARP) cache.
Defines static host name-to-address mapping in the host cache.
Enables IPv6 processing on an interface.
Sets an IPv6 address on an interface.
Configures an IPv6 link-local address for an interface.
Defines an IPv6 default gateway.
Identifies a specific line for configuration and enters Line Configuration mode.
Enables Dynamic Host Configuration Protocol (DHCP) option-82 data insertion.
Enables Dynamic Host Configuration Protocol (DHCP) relay features globally.
Enables Dynamic Host Configuration Protocol (DHCP) relay features for an interface.
Makes a DHCP server available for the DHCP relay.
Configures the system priority.
Configures physical port priority.
Enables the Link Layer Discovery Protocol (LLDP).
Enables LLDP on an interface.
Configures the login banner, a security message displayed before login.
Configures a management Access List and enters Management Access-list Configuration mode.
Defines a permit rule for management access.
Defines a deny rule for management access.
Restricts management connections by defining the active management Access List.
Diagnoses copper cable quality using Time Domain Reflectometry (TDR).
Enters interface configuration mode to configure a specific port-channel.
Enters interface configuration mode to configure multiple port-channels.
Associates a port with a port-channel.
Starts a port monitoring session.
Configures the administrative mode of inline power on an interface.
Configures the inline power management priority of the interface.
Enables quality of service (QoS) on the device.
Limits the rate of the incoming traffic.
Sets a shaper on an egress interface.
Specifies a RADIUS server host.
Displays RMON Ethernet statistics.
Displays RMON Ethernet history statistics.
Configures alarm conditions.
Configures the community access string for SNMP protocol access.
Specifies the SNMP engineID on the local device.
Enables spanning-tree functionality.
Configures the spanning-tree protocol (STP, RSTP, or MSTP).
Configures the spanning tree priority of the device.
Disables spanning tree on a specific port.
Configures the spanning tree path cost for a port.
Configures port priority.
Configures device priority for a specified spanning-tree instance.
Configures port priority for the specified MST instance.
Configures path cost for multiple spanning tree (MST) calculations.
Shows spanning tree configuration.
Specifies the port to be used by the SSH server.
Enables public key authentication for incoming SSH sessions.
Controls error message logging.
Logs messages to a syslog server.
Specifies a TACACS+ host.
Enters tunnel interface configuration mode.
Sends ICMP echo request packets to another node on the network.
Specifies or modifies the device host name.
Enters the Privileged EXEC mode.
Enters the Global Configuration mode.
Enters the VLAN Configuration mode.
Creates a VLAN.
Enters the Interface Configuration (VLAN) mode.
Configures the VLAN membership mode of a port.
Configures the VLAN ID when the interface is in access mode.
Adds or removes VLANs to or from a trunk port.
Enables configuring the device from a browser.
Enables configuring the device from a secured browser.
Specifies authentication, authorization, and accounting (AAA) methods for 802.1X interfaces.
Enables 802.1x globally.
Manually controls the authorization state of the port.
To Next Page
