Home
Ametek
Measuring Instruments
HAG
Ametek HAG User Manual
4
of 1
of 1 rating
92 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
4-16 | Heated
Acid Gas Sample Probe (Large Diameter)
List of Materials and Special T
ools Required
While working on the Heater Assembly
, certain special tools and materials
are required. These include:
•
Soldering iron
• Solder
•
High-temperature wire (for ground wire)
•
High-temperature thread lubricant (must not contain copper)
•
O
-ring removal tools
•
Soft, non-abrasive cloth
67
69
Table of Contents
Default Chapter
2
Offices
2
Table of Contents
3
Electrical Safety
5
Grounding
5
Safety Notes
5
Personnel and Equipment Safety Information
6
Warnings
6
Cautions
7
Warning Labels
8
Environmental Information
8
Electromagnetic Compatibility (EMC)
9
Special Warnings and Information
10
Equipment Used in Hazardous Locations
10
EU Declaration of Conformity
11
Warranty and Claims
12
Chapter 1 Overview
13
About the Heated Acid Gas Sample Probe
14
About the Analyzer Sample System
17
Working in this Manual
20
Chapter 2 Specifications
21
Probe Heater
21
Power Consumption
21
Electrical Requirements
21
Approvals and Certifications
21
Ingress Protection
22
Ambient Limits
22
Cable/Cable Glands
22
Probe Valve Assembly
22
Typical Flow Rate
22
Aspirator Drive Gas (Sample Transport)
22
Minimum Ambient Temperature
23
Maximum Process Temperature
23
Minimum Probe Temperature
23
Maximum Probe Pressure
23
Process Connection
23
Physical Dimensions
23
ATEX and Iecex Certificates and Marking
24
Chapter 3 Installation and Start-Up
31
Safety Considerations
32
Pre-Installation Requirements
33
Storage Prior to Installation
33
Uncrating and Inspecting the HAG Sample Probe
33
Tools and Equipment Required
33
Installing the Heated Acid Gas Sample Probe
34
Installing the HAG Sample Probe in New Applications
35
Retrofitting the HAG Sample Probe
39
Connecting the Aspirator Drive Gas Line
44
Connecting Signals and AC Power
45
Wiring Sample Probe Heaters Controlled by Analyzer
45
Wiring Sample Probe Heaters Controlled by Standalone Temperature Controller (Retrofits)
48
Powering up the Probe Heater Assembly and Analyzer
50
Chapter 4 Maintenance
53
Safety Considerations
53
Preventive Maintenance Schedule
54
Preparing the Analyzer and Probe for Maintenance
56
Changing out Replaceable Parts
58
Replacing HAG Probe Parts
58
Replacing Probe Heater Parts - Extended Maintenance
67
List of Materials and Special Tools Required
68
Examining and Caring for the Flamepaths
79
Chapter 5 Service and Parts
81
Technical Support
81
Ametek Service & Aftermarket Sales Support
82
Recommended Spare Parts
83
Preventive Maintenance Spare Parts
83
Extended Maintenance Spare Parts
84
Chapter 6 Drawings
85
Heated Acid Gas Sample Probe Assembly (100-2196)
86
Probe Heater Assembly, 120 V / 240 V (100-1658-1A)
87
Double Block Valve Assembly (100-2393)
88
Fiber Filter Assembly (100-2194)
89
Supplemental Information
91
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Ametek HAG and is the answer not in the manual?
Ask a question
Ametek HAG Specifications
General
Brand
Ametek
Model
HAG
Category
Measuring Instruments
Language
English
Related product manuals
Ametek 5100 HD
134 pages
Ametek 900
256 pages
Ametek 5000
52 pages
Ametek mAcal
15 pages
Ametek 3050-DO
83 pages
Ametek 241CE II
192 pages
Ametek 3050 Series
86 pages
Ametek Thermox WDG-V
164 pages
Ametek BROOKFIELD CT3
64 pages
Ametek SPECTRO ARCOS FHX3X
71 pages
Ametek mocon Dansensor ISM-3
34 pages
Ametek Land Cyclops L Series
60 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
