Anritsu MT8852B - Remote Programming Manual

Anritsu MT8852B

309 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

®

MT8852B

Remote Programming Manual

Bluetooth Test Set

Table of Contents

Default Chapter12
- Table of Contents12
Chapter 1-General Information20
- About this Manual20
- Command Format22
Chapter 2-GPIB Overview24
- Requirements When Using GPIB24
- Syntax24
- Termination25
- Suffixes25
- GPIB 488.2 Registers26
- GPIB over RS23234
- Summary of RS232 Commands35
Chapter 3-IEEE 488.2 Mandatory and Register Commands36
- CHE (Change Enable Register)36
- CHG (Change Register)36
- CLS (Clear GPIB Status Bytes)37
- EETE (EDR EUT Fail Enable Register)37
- EETF (EDR EUT Fail Register Query)38
- ESE (Standard Event Status Enable)38
- ESR (Standard Event Status Register Query)39
- ETE (EUT Fail Enable Register)39
- ETF (EUT Fail Register Query)40
- IDN (Identification Query)40
- INE (Instrument Status Enable Register)41
- INS (Instrument Status Register Query)41
- LEETE (BLE EUT Fail Enable Register)42
- LEETF (BLE EUT Fail Register Query)42
- OPC (Operation Completed Indication)43
- RST (Instrument Reset)43
- SRE (Service Request Enable Register)44
- STB (Status Byte Register Query)44
- TST (Self Test Query)45
- WAI (Wait to Continue)45
Chapter 4-General GPIB Commands46
- BOOTSTATUS? (Startup Self Test Status Request )46
- CONT (Continue after Self Test)46
- ERRLST (Error List)47
- EUTINIT (Bluetooth Slave Mode)49
- EUTMAXPWR (Send EUT to Max Power Control)49
- LEPKTLEN (Set the BLE Data Packet Length)49
- LEPKTMODE (Set the BLE Data Packet Mode)50
- LKPASS (Update Lock/Unlock Password)50
- LOCK (Script Lock)51
- OPMD (Operation Mode)52
- OPTSTATUS? (Option Status)54
- SCPTCFG (Configure Script)54
- SCPTNM (Set Script Name)57
- SCPTRST (Reset Script)57
- SCPTSEL (Select Script)58
- SCPTTSTGP (Set Test Group State)58
- SCRIPTMODE (Script Mode)59
- STATUS (Status Command)60
- STERR (Request POST or *TST? Results)63
- Self Test Items63
- TSTPAUSE (Test Pause)65
- TXPWR (Transmitter Power Level)65
- UNLOCK (Script Unlock)66
Chapter 5-System Configuration68
- SYSCFG (Set or Query System Configuration)68
- AUTH (Authentication Settings)69
- BNCOUTPUT (Rear Panel Output)70
- BTADDR (Tester Bluetooth Address)70
- CONFIG (Tester Configuration)71
- DISPSOUND (Tester Display and Sound Control)78
- EUTADDR (EUT Address)82
- EUTFEAT (EUT Supported Features)82
- EUTHANDSHAKE (EUT RS232 Handshake Setting)82
- EUTNAME (EUT User Friendly Name Request)83
- EUTRS232 (EUT RS232 HCI Set Up)83
- EUTSRCE (EUT Address Source)85
- HWINFO (Hardware Information)86
- IDENT (Tester Identity)86
- INQSET (Inquiry Set Up)87
- Pagset89
- SCPTSET (Script Set Up)90
- USBADAPTOR (Adaptor Set Up)92
- VERDATE (Tester Firmware Version and Date Stamp)93
- VERNUM (Tester Firmware Version Numbers)93
Chapter 6-SCO Configuration94
- SCOCFG (Set SCO Configuration)94
Chapter 7-SCO Connections100
- SCOCONN (SCO Connect)100
- SCODISC (SCO Disconnect)100
Chapter 8-AFH Measurement102
- AFHCFG (Set AFH Configuration)102
Chapter 9-Signal Generator Mode and CW Measurement108
- Basic Rate Signal Generator Mode108
- BLE Signal Generator Mode109
- BLE Extended Signal Generator Mode (Supports Data Length Extension)110
- BLE Extended Signal Generator Mode (Supports Bluetooth 5 - 2LE and BLR)9-4111
- EDR Signal Generator Mode113
- CW Measurement Mode114
- EDR CW Measurement Mode115
- CWRESULT (CW Measurements Results Output)116
- ECWRESULT (EDR CW Measurements Results Output) (MT8852B and117
Chapter 10-Configuring Tests in Standard Mode118
- Basic Rate Tests120
- Enhanced Data Rate Tests138
- Low Energy Tests151
Chapter 11-Configuring Tests in Single Payload Mode166
- Single Payload Configuration (SPCFG)166
Chapter 12-Test Parameter Variables168
- Actual Frequencies Used168
- Default171
- Dhxpkt171
- Dirtytab172
- Dirtytx173
- Frequencies Used (LFREQSEL, MFREQSEL, HFREQSEL)174
- Drifts175
- Ferlimmode175
- Hopmode176
- Hopping177
- Hopstate178
- Lepkttype179
- Letstmode181
- Mincheck182
- Numbits183
- Minpwr183
- Numblks184
- Numcyc184
- Numpkts185
- Payload186
- Pktcount186
- Pktnummode187
- Pktsize188
- Pkttype189
- Ptxlev190
- Pwrdelay190
- Thbitcnt191
- Toggle191
- Tstctrl192
- Ttbitcnt193
- Txpwr193
Chapter 13-Test Limit Variables194
- Output Power Test Limit Commands194
- Power Control Test Limit Commands195
- Enhanced Power Control Test Limit Commands196
- Initial Carrier Frequency Test Limit Commands197
- Carrier Frequency Drift Limit Commands198
- Standard Rate Sensitivity Test Limit Commands199
- Modulation Index Limit Commands200
- EDR Relative Transmit Power Limit Commands201
- EDR Carrier Frequency and Accuracy Limit Commands203
- EDR Differential Phase Encoding Limit Commands210
- EDR Sensitivity and EDR BER Floor Limit Commands211
- EDR Maximum Input Power Limits213
- BLE Output Power Test Limit Commands214
- BLE Carrier Frequency Offset and Drift Limit Commands215
- BLE Modulation Characteristics Limit Commands217
- BLE Sensitivity Test and Maximum Input Limit Commands220
- BLE PER Report Integrity Test Limit Commands221
Chapter 14-Running And Aborting Code222
- Running Tests (RUN)222
- Aborting Tests (ABORT)222
Chapter 15-Reading Test Results Data224
- Summary Results225
- Summary Results Output Format228
- Extended Results Data Output231
- Extended Results Output Format234
- Basic Rate Tests237
- EDR Tests250
- Low Energy Tests267
Chapter 16-BLE Measurement276
- ABORTCAP Abort the BLE Measurement Capture276
- CFGBLECAP (Configure BLE Capture)276
- LESCPTCFG (Configure All Measurements in a Script in Parallel)277
- MEASBLECAP (Capture and Make BLE Tx Measurement)278
- MEASBLECAPX (Capture and Make BLE Tx Measurement - Extended)279
- SETBLECAPTYP (Set the Capture Type to BLE, 2LE or BLR)280
- Example BLE Measurement281
Chapter 17-Auxiliary Commands282
- CONNECT (Connect to EUT Address)283
- CONEUTNAME (Read EUT User Name on a Connection)283
- CONNPKT (Connection Packet Control)284
- CONTIME? (Connection Time) (Option 15 Required)284
- DISCONNECT (Disconnect from Device)285
- EUTRESET (Send HCI Reset to the DUT)285
- EUTRMTPWR (Change the State of the EUT Tx Power)285
- EUTVENDCMD (Send a Vendor-Specific Command to EUT)286
- FIXEDOFF (Set Fixed Offset Value)288
- GETEUTFEAT (Obtain Supported Features from EUT)288
- INQCANCEL (Cancel an Inquiry)288
- INQRSP? (Obtain the Results of an Inquiry)289
- INQUIRY (Perform an Inquiry)289
- LOOPBACK (Perform a Loopback Test Control Sequence)290
- PATHDEL (Delete an Entry from a Path Loss Table)291
- PATHEDIT (Add or Change Entries in a Path Loss Table)291
- PATHOFF (Set Path Offset Mode)292
- PATHRD (Read a Complete Path Loss Table)292
- PATHTBL (Set Path Offset Table)293
- PATHTBLCLR (Clear a User Path Table)293
- TESTMODE (Put the EUT into Test Mode)293
- TSTDELAY (Test Control Delay)294
- TXTEST (Perform a Tx Test Control Sequence)295
- WRDTY (Write the Dirty Parameter Settings to the Core)295
Appendix A-Supported Features Format296
- EUT Feature Format296
Appendix B-Gpib PC Card Set-Up298
- GPIB Card Settings298
- GPIB Device Template298
Appendix C-Script Default Settings300
- Script 1 Default Settings301
- Script 2 Default Settings301
- C-3 Scripts 3 to 10 Default Settings302
- Scripts 3 to 10 Default Settings303

Other manuals for Anritsu MT8852B

Operation Manual239 pages

Related product manuals

Preview: Anritsu MT1000A

Anritsu MT1000A

Preview: Network Master Pro MT1000A

Network Master Pro MT1000A

Preview: Anritsu LMR Master S412E

Anritsu LMR Master S412E

Preview: Anritsu Site Master S113B

Anritsu Site Master S113B

VectorStar MN469xC Series

Preview: VectorStar MN469 C Series

VectorStar MN469 C Series

Preview: Anritsu 681XXC