Need help?Do you have a question about the APC 750 VA and is the answer not in the manual?
Critical safety instructions and hazard warnings for UPS operation.
Guidelines for safe installation, operation, and handling of the UPS.
Details on the UPS front panel interface and controls.
Details on the UPS rear panel connectors and protection.
Operating temperature, humidity, and elevation limits for the UPS.
Steps to connect peripheral devices and utility power to the UPS.
Identification of UPS display interface indicators and controls.
Navigation and usage of the UPS display interface menus.
View basic UPS information like operating mode, load, and battery status.
Configure UPS settings such as language, power quality, and display.
Perform UPS self-tests, alarm tests, and calibration.
Display unit information like model number and firmware version.
View detailed UPS information like energy meter and load current.
Configure advanced settings like outlet group delays and transfer points.
Control main and switched outlet groups for power management.
Perform advanced UPS tests and diagnostics.
View event and error logs for UPS changes and faults.
View advanced unit information like hardware and software versions.
Configure language and local power quality settings at startup.
Initial configuration of UPS language and power quality.
Set the voltage threshold for switching to battery power.
Set the lower voltage threshold for switching to battery power.
Set the UPS output voltage when on battery.
Adjust UPS tolerance to power fluctuations.
Configure the audible alarm threshold for low battery runtime.
Record the date of battery replacement for maintenance tracking.
Enable or disable audible alarms on the UPS.
Schedule automatic UPS battery self-tests.
Restore the UPS to its original factory default settings.
Understanding the functionality of Main and Controlled Outlet Groups.
Connect and configure critical and peripheral equipment to outlet groups.
Set names, turn-on/off delays for outlet groups.
Configure reboot duration and minimum runtime for outlet groups.
Configure load shedding based on battery status or runtime.
Configure outlet group behavior during overload conditions.
Configure network settings via NMC interface.
How the EPO feature immediately disconnects power to connected equipment.
Instructions for wiring normally open and normally closed EPO contacts.
Diagnose and resolve issues preventing UPS startup or output.
Troubleshoot why the UPS is running on battery power.
Interpreting intermittent beeps from the UPS.
Address issues causing the UPS to provide less backup time than expected.
Interpret sequential flashing of display interface LEDs.
Address internal UPS faults indicated by the Fault LED.
Diagnose the cause of all UPS LEDs being illuminated.
Troubleshoot issues related to a weak or improperly connected battery.
Identify and resolve site wiring faults affecting UPS operation.
Steps to contact APC support for troubleshooting and service.
Instructions for safely packing and shipping the UPS for service.
Critical safety instructions and hazard warnings for UPS operation.
Guidelines for safe installation, operation, and handling of the UPS.
Details on the UPS front panel interface and controls.
Details on the UPS rear panel connectors and protection.
Operating temperature, humidity, and elevation limits for the UPS.
Steps to connect peripheral devices and utility power to the UPS.
Identification of UPS display interface indicators and controls.
Navigation and usage of the UPS display interface menus.
View basic UPS information like operating mode, load, and battery status.
Configure UPS settings such as language, power quality, and display.
Perform UPS self-tests, alarm tests, and calibration.
Display unit information like model number and firmware version.
View detailed UPS information like energy meter and load current.
Configure advanced settings like outlet group delays and transfer points.
Control main and switched outlet groups for power management.
Perform advanced UPS tests and diagnostics.
View event and error logs for UPS changes and faults.
View advanced unit information like hardware and software versions.
Configure language and local power quality settings at startup.
Initial configuration of UPS language and power quality.
Set the voltage threshold for switching to battery power.
Set the lower voltage threshold for switching to battery power.
Set the UPS output voltage when on battery.
Adjust UPS tolerance to power fluctuations.
Configure the audible alarm threshold for low battery runtime.
Record the date of battery replacement for maintenance tracking.
Enable or disable audible alarms on the UPS.
Schedule automatic UPS battery self-tests.
Restore the UPS to its original factory default settings.
Understanding the functionality of Main and Controlled Outlet Groups.
Connect and configure critical and peripheral equipment to outlet groups.
Set names, turn-on/off delays for outlet groups.
Configure reboot duration and minimum runtime for outlet groups.
Configure load shedding based on battery status or runtime.
Configure outlet group behavior during overload conditions.
Configure network settings via NMC interface.
How the EPO feature immediately disconnects power to connected equipment.
Instructions for wiring normally open and normally closed EPO contacts.
Diagnose and resolve issues preventing UPS startup or output.
Troubleshoot why the UPS is running on battery power.
Interpreting intermittent beeps from the UPS.
Address issues causing the UPS to provide less backup time than expected.
Interpret sequential flashing of display interface LEDs.
Address internal UPS faults indicated by the Fault LED.
Diagnose the cause of all UPS LEDs being illuminated.
Troubleshoot issues related to a weak or improperly connected battery.
Identify and resolve site wiring faults affecting UPS operation.
Steps to contact APC support for troubleshooting and service.
Instructions for safely packing and shipping the UPS for service.
General| Capacity | 750 VA |
|---|---|
| Input Voltage | 230V |
| Output Voltage | 230V |
| Form Factor | Tower |
| Waveform | Stepped approximation to a sinewave |
| Communication Port | USB |
| Output Power Capacity | 450 W |
| Input Connection | IEC 320 C14 |
| Frequency | 50/60 Hz |
| Operating Temperature | 0°C to 40°C |
| Storage Temperature | -15°C to 45°C |
| Humidity | 0 - 95% relative humidity, non-condensing |
| Battery Type | Sealed Lead Acid |
To Next Page
