Why does my Argox R-400plus have vertical streaks in the printout?
If you observe vertical streaks in the printout from your Argox printer, it might be due to a dirty or faulty print head. First, try cleaning the print head. If the streaks persist after cleaning, consider replacing the print head.
How to improve poor printout quality on my Argox R-400plus Printer?
If your Argox Printer's printout quality is poor, several factors could be responsible. The ribbon or the media might not be qualified for printing. Try adjusting the darkness (heat temperature) settings. Alternatively, slowing down the print speed may improve the printout quality.
What to do if my Argox R-400plus Printer is timing out?
If your Argox Printer is timing out, ensure the communication cable is securely connected. Also, verify that the printer power is turned on. If the power cord is connected, the power switch is at the correct position, and the power LED is still not illuminated, it may require professional service.
Why is there no output from my Argox Printer?
If there is no output from your Argox printer, check that the active printer driver is Label Dr. for your Windows system and the label printer. Also, verify the emulation and the print (command) file.
How to fix missing gap error on Argox R-400plus Printer?
If your Argox printer is showing a missing gap error, check the media path and the position of the label sensor. If you are using continuous media, verify that your application software and driver are set to continuous.
Why is the ribbon roll rotation unstable in my Argox R-400plus Printer?
If the ribbon roll rotation is unstable on your Argox printer, check the label path. Also, make sure the head latch is securely closed.
Manual contains proprietary information of Argox Information Co., Ltd.
Continuous improvement of products is a policy of Argox Information Co., Ltd.
Equipment tested and found to comply with limits for a Class A digital device.
Argox Information Co., Ltd. reserves the right to correct errors.
Limits liability for damages arising from product use.
Instructions for checking printer and accessories upon receipt.
Guide on connecting the printer to the power supply and AC source.
Overview of the printer's main components and controls.
Explains the function of the power switch and control buttons.
Description of the LED indicators and their status meanings.
Step-by-step guide for calibrating the printer for label size detection.
Instructions on how to print a self-test page.
Procedure to reset the printer's settings to default.
Step-by-step guide for loading the ribbon into the printer.
Guide for loading media, including standard, peel-off, and cutter modes.
Detailed steps for loading media in standard mode.
Detailed steps for loading media in peel-off mode.
Detailed steps for loading media in cutter mode.
Details on connecting the printer to a computer via various cables.
Information on using the bundled printer driver with Windows applications.
Guide for installing printer drivers for non-USB interfaces.
Common media issues and their solutions.
Common ribbon issues and their solutions.
Addresses miscellaneous problems like timeouts and no output.
Steps to resume printer operation after issues.
Detailed instructions for print head cleaning.
Procedures for cleaning the roller and media compartment.
Overview of the printer's general technical specifications.
Details on supported fonts, barcodes, and graphics.
Specifications for the PPLA programming language.
Specifications for the PPLB programming language.
Specifications for the PPLZ programming language.
Pin assignments and signal descriptions for the serial port.
Details on the USB connection and its pin assignment.
Information on connecting the printer to a host computer.
Pin assignments for the parallel port.
Information on auto polling and the ASCII character table.
Explains LED status meanings and basic troubleshooting.
Operating the printer with keyboards/scanners.
Step-by-step guide for installing the dispenser kit.
Step-by-step guide for installing the cutter accessory.
General| Print technology | Direct thermal / Thermal transfer |
|---|---|
| Maximum resolution | 203 x 203 DPI |
| Maximum print height | 1092 mm |
| Maximum printing width | 108 mm |
| Wi-Fi | - |
| USB port | Yes |
| Ethernet LAN | No |
| Optional connectivity | Bluetooth, Ethernet, Wireless LAN |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Connectivity technology | Wired & Wireless |
| Parallel ports quantity | 1 |
| Certification | CE, FCC, UL, CUL, CCC, RoHS |
| Internal memory | 2 MB |
| Number of fonts | 5 |
| Built-in barcodes | 1D, 2D, CODABAR (NW-7), Code 11, Code 128 (A/B/C), Code 39, Code 93, EAN128, EAN13, EAN8, Industrial 2/5, Interleaved 2/5, Matrix 2/5, MaxiCode, PDF417, POSTNET, UPC-A, UPC-E |
| Built-in processor | 32-bit RISC |
| Image formats supported | BMP, IMG, PCX |
| Product color | Black |
| Ribbon width | 101.6 mm |
| Core diameter | 25.4 mm |
| Ribbon length | 360 m |
| Media thickness | 0.254 mm |
| Maximum roll diameter | 152 mm |
| LED indicators | Power, Ready, Status |
| Media types supported | Roll-feed, die-cut, continuous, fan-fold, tags, ticket in thermal paper / plain paper, fabric label |
| Storage temperature (T-T) | -20 - 50 °C |
| Operating temperature (T-T) | 4 - 38 °C |
| Operating relative humidity (H-H) | 0 - 90 % |
| Bundled software | BarTender, ArgoBar Pro, Printer Utility, Font Utility |
| Power requirements | 100V - 240V AC, 50 - 60Hz |
| Compatible operating systems | Windows 2000/XP/Vista/7 |
Weight and Dimensions| Depth | 314 mm |
|---|---|
| Width | 231 mm |
| Height | 218 mm |
| Weight | 4200 g |
To Next Page
