EasyManua.ls Logo

Assa Abloy Norton 6000 Series - User Manual

Assa Abloy Norton 6000 Series
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Copyright © 2017 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
80-9360-1020-020 Rev 1 02/17
6000 Series
6010LAP / 6020LAP Replacement
Installation and Instruction Manual
ETL certified; conforms to ANSI/UL standard
325 for automatic closing doors and UL10C
Positive Pressure Fire Test for Door Assemblies.
Certified to ANSI/BHMA A156.19 for Low Energy
Door Operators.
WARNING: To reduce the risk of injury to person,
use this operator only with Pedestrian Swing doors.
For Indoor Use Only.
IMPORTANT INSTALLATION INSTRUCTIONS
1) READ AND FOLLOW ALL INSTALLATION
INSTRUCTIONS.
2) Install only on a properly operating and balanced door. A
door that is operating improperly could cause severe
injury. Have qualified service personnel make repairs to
any hardware before installing the operator.
3) Remove, or make inoperative, all locks (unless
mechanically and/or electrically interlocked to the
power unit) that are connected to the door before
installing the operator.
4) Do not connect the door operator to the source
power until instructed to do so.
!
WARNING: Make sure that (120V, 60Hz) input power is turned off at facility’s main
circuit breaker before proceeding with installation.
For replacement of 6010LAP on
existing 6010 or 6050 installs,
see page 2.
For replacement of 6020LAP on
existing 6060 or 6070 installs,
see page 6.
For replacement of 6020LAP on
existing 6020 or 6030 installs,
see page 4.

Table of Contents

Other manuals for Assa Abloy Norton 6000 Series

Preview: Programming Instructions
Programming Instructions34 pages

Questions and Answers

  • A
    annamooreAug 14, 2025
    What to do if Assa Abloy Door Opening System opens and closes repeatedly?
    • J
      joelparkerAug 14, 2025
      If your Assa Abloy Door Opening System is opening and closing repeatedly, change the Selector Mode switch from H/O to On.
  • G
    glenngomezAug 17, 2025
    What to do if Assa Abloy Norton 6000 Door Opening System motor is driving in the wrong direction?
    • M
      Maria PageAug 18, 2025
      If the motor of your Assa Abloy Door Opening System is driving in the wrong direction, change the Arm Type (Push / Pull). A new Setup is required.
  • C
    Cody Nunez Jr.Aug 21, 2025
    What to do if Assa Abloy Norton 6000 Door Opening System displays error message “Short Circuit”?
    • R
      reyesjasonAug 21, 2025
      If your Assa Abloy Door Opening System displays a “Short Circuit” error message, turn off the power to the unit and check the wiring for a short or cut.
  • J
    Jason MillsAug 25, 2025
    What to do if Assa Abloy Norton 6000 does not open to desired location?
    • R
      Robin PerezAug 25, 2025
      If your Assa Abloy Door Opening System doesn't open to the desired location: 1) Repeat the Open Position setup process, OR 2) Increase the Obst Delay.
  • C
    Christopher KellerAug 28, 2025
    What to do if Assa Abloy Norton 6000 does not reach fully opened position?
    • J
      Jordan MooreAug 28, 2025
      If your Assa Abloy Door Opening System does not reach the fully opened position: 1) Repeat the Open Position setup process, OR 2) Increase the Obst Delay.
  • L
    laura37Aug 31, 2025
    What to do if Assa Abloy Door Opening System tries to open door before auxiliary components are unlatched / retracted?
    • B
      Bethany Rodriguez MDAug 31, 2025
      If, when a signal is received, your Assa Abloy Door Opening System tries to open the door before auxiliary components are unlatched or retracted: 1) Confirm that the latch devices are getting proper power, 2) Confirm that the latch devices are receiving power long enough to fully retract - adjust Latch Retraction on the controller as needed, 3) If the latch device is not retracting fast enough, increase the Start Delay on the controller to assure the latch device has had sufficient time to fully retract before the operator starts opening the door.
  • M
    Mindy VelasquezSep 3, 2025
    What to do if Assa Abloy Norton 6000 Door Opening System drifts toward closed position when door reaches open position?
    • S
      Sherry TaylorSep 3, 2025
      If your Assa Abloy Door Opening System drifts toward the closed position when the door reaches the open position, increase the Hold Speed until the door stops drifting.
  • B
    Breanna RodriguezSep 7, 2025
    What to do if Assa Abloy Norton 6000 Door Opening System drifts further open when door reaches open position?
    • C
      Crystal SteeleSep 7, 2025
      If your Assa Abloy Door Opening System drifts further open when the door reaches the open position, decrease the Hold Speed until the door stops drifting.
  • M
    Megan BeckerSep 12, 2025
    What to do if Assa Abloy Norton 6000 bounces when door reaches open position?
    • J
      Jennifer ValdezSep 12, 2025
      If your Assa Abloy Door Opening System bounces when the door reaches the open position, decrease the Slow Speed.

Summary

Important Installation Instructions

Critical Safety Warnings

Key safety warnings regarding power, injury risk, and indoor use.

Turn Off Power

Disconnect and Assemble Arm and Closer

Disconnect Arm From Track (6010;6050 Units)

Procedure for disconnecting the arm from the slide assembly.

Remove Arm Screw From Pinion

Steps to remove the arm screw from the pinion.

Disassemble Arm From Pinion

Instructions for disassembling the arm from the pinion.

Disassemble Closer Sub-Assembly

Steps to disassemble the closer sub-assembly.

Assembly Closer Sub-Assembly

Procedure for installing the closer sub-assembly.

Assemble Arm to Pinion

Instructions for assembling the arm to the pinion.

Secure Arm to Pinion

Steps to secure the arm to the pinion.

Connect Arm To Track

Procedure for connecting the arm to the track.

Install Closer for 6020;6030 Units

Loosen Arm Assembly

Steps to loosen the arm assembly for 6020/6030 units.

Remove Screw and Arm from Pinion

Instructions for removing the screw and arm from the pinion.

Install Closer for 6060;6070 Units

Loosen Adjusting Rod and Arm Slide Tube

Steps to loosen adjusting rod and arm slide tube.

Secure Adjusting Rod and Arm Slide Tube

Procedure for securing adjusting rod and arm slide tube.

Disassemble and Assemble Closer for 6060;6070 Units

Remove Arm from Pinion

Instructions for removing the arm from the pinion.

Disassemble Closer Sub-Assembly

Steps to disassemble the closer sub-assembly.

Assembly Closer Sub-Assembly

Procedure for installing the closer sub-assembly.

Assemble Arm to Pinion

Instructions for assembling the arm to the pinion.

Secure Arm to Pinion

Steps to secure the arm to the pinion.

Secure Adjusting Rod and Arm Slide Tube

Procedure for securing adjusting rod and arm slide tube.

Closer Spring Force Adjustment

Mechanical Closer Adjustments

Closing Speed Controls

Adjustments for Sweep (S) and Latch (L) speed ranges.

Back Check Adjustments

Controls for Back Check (B) cushioning and position (P).

Controller Interface

Set Home and Open Positions

Install Cover and Label

General Electrical Information

Wiring Specifications

Details on power input, wire size, and voltage requirements.

Alarm System Integration

Requirements for fire/smoke barrier door assemblies.

Controller Interface Description

Screen Display and Adjustments

Overview of controller screen display options and adjustments.

Setting Home and Open Positions

Description of setting home and open positions.

Assa Abloy Norton 6000 Series Specifications

General IconGeneral
BrandAssa Abloy
ModelNorton 6000 Series
CategoryDoor Opening System
LanguageEnglish

Related product manuals