AUMA SA 07.2 - Page 103

To Next Page

To Previous Page

103

SA 07.2 – SA 16.2 / SAR 07.2 – SAR 16.2 Control unit: electronic (MWG)

AC 01.2 Non-Intrusive DeviceNet

Main Page

Table of Contents2
Safety Instructions5
Prerequisites for the Safe Handling of the Product5
Range of Application5
Warnings and Notes6
References and Symbols6
Short Description7
Name Plate9
Transport and Storage13
Transport13
Storage15
Assembly17
Mounting Position17
Handwheel Fitting17
Mount Actuator to Valve17
Overview of Output Drive Types18
Output Drive Type a18
5.3.2.1. Multi-Turn Actuator with Output Drive Type A: Mount19
5.3.2.2. Stem Nut for Output Drive Type A: Finish Machining21
Output Drive Types B/C/D and E22
5.3.3.1. Multi-Turn Actuator with Output Drive Type B: Mount23
Accessories for Assembly24
Stem Protection Tube for Rising Valve Stem24
Mounting Positions of Local Controls25
Mounting Positions: Modify25
Electrical Connection26
Overview of AUMA Electrical Connections26
Basic Information26
SJ Electrical Connection (AUMA Plug/Socket Connector)29
Terminal Compartment (for Mains Connection): Open30
Cable Connection31
Terminal Compartment (for Mains Connection): Close32
Fieldbus Terminal Compartment: Open33
Devicenet Cable: Connect33
Fieldbus Terminal Compartment: Close34
Accessories for Electrical Connection35
Actuator Controls on Wall Bracket35
Parking Frame36
DS Intermediate Frame for Double Sealing36
External Earth Connection37
Operation38
Manual Operation38
Manual Valve Operation38
Motor Operation39
Operating the Actuator from Local Controls39
Actuator Operation from Remote40
Menu Navigation Via Push Buttons (for Settings and Indications)40
Menu Layout and Navigation41
User Level, Password42
Password Entry43
Password Change43
Timeout for Incorrect Password Entry44
Language in the Display44
Language Change44
Indications46
Indications During Commissioning46
Indications in the Display46
Feedback Signals from Actuator and Valve47
Status Indications According to AUMA Classification49
Status Indications According to NAMUR Recommendation50
Indication Lights of Local Controls52
Optional Indications53
Mechanical Position Indication Via Indicator Mark (Not Self-Adjusting)53
Mechanical Position Indication (Self-Adjusting)53
Signals (Output Signals)54
Signals Via Devicenet54
Status Signals Via Output Contacts (Digital Outputs)54
Assignment of Outputs54
Coding the Outputs54
Analogue Signals (Analogue Outputs)54
Commissioning (Basic Settings)56
Type of Seating: Set56
Torque Switching: Set57
Limit Switching: Set59
Settings at the Devicenet Gateway61
Fieldbus Address and Baud Rate Setting61
Termination61
Input and Output Data61
Led70
Test Run71
Direction of Rotation at Mechanical Position Indicator: Check71
Direction of Rotation at Hollow Shaft/Stem: Check73
Limit Switching: Check73
Commissioning (Settings/Options in the Actuator)75
Switch Compartment: Open/Close75
Mechanical Position Indicator (Self-Adjusting)76
Mechanical Position Indicator: Set76
Gear Stage of the Reduction Gearing: Test/Set77
Mechanical Position Indication Via Indicator Mark (Not Self-Adjusting)78
Mechanical Position Indicator: Set78
Gear Stage of the Reduction Gearing: Test/Set78
Corrective Action81
Faults During Commissioning81
Fault Indications and Warning Indications81
Fuses85
Fuses Within the Actuator Controls85
Fuse Replacement86
Replace Fuses86
Test/Replace Fuses86
Motor Protection (Thermal Monitoring)87
Servicing and Maintenance88
Preventive Measures for Servicing and Safe Operation88
Maintenance89
Disposal and Recycling89
Technical Data90
Technical Data Multi-Turn Actuators90
Technical Data Actuator Controls92
Tightening Torques for Screws97
Spare Parts99
Multi-Turn Actuators SA99
Sa 16.2/Sar 07.299
Sar 16.299
AC 01.2 Actuator Controls with SJ Electrical Connection101
Index105

AUMA SA 07.2 - Page 103

Table of Contents

Other manuals for AUMA SA 07.2

Related product manuals