Need help?Do you have a question about the Automationdirect.com Stride SE3 Series and is the answer not in the manual?
General| Ports | 5, 8, or 16 |
|---|---|
| Data Transfer Rate | 10/100 Mbps |
| Mounting | DIN Rail |
| Model | SE3 Series |
| Type | Unmanaged Ethernet Switch |
| Power Input | 12-48 VDC |
| Protocol Support | IEEE 802.3, IEEE 802.3u |
| Dimensions | Varies by model |
Manual describes Stride industrial Ethernet switches, specifications, components, and setup information.
Information on how to contact technical support and visit the website for assistance.
Explains the meaning of icons and bold text used in the manual for warnings and notes.
Provides a brief introduction to the manual's purpose and ease of installation.
Explains how Stride industrial Ethernet switches intelligently route messages for improved performance.
Advises on considering security exposure when implementing remote access to equipment.
Details requirements for installing and operating units in Class 1, Division 2 hazardous locations.
Explains the meaning of caution and hot surface warning labels.
States compliance with FCC rules for Class-A digital devices and provides measures to correct interference.
Notes that the product is Class-A and may cause radio interference in domestic environments.
Lists features and models of SE3 industrial unmanaged Ethernet switches.
Describes Stride SFP transceivers and their use for adding fiber connectivity.
Details the function of LED indicators for various SE3 switch models.
Explains the power fault alarm contact and its function.
Details the DIP switch settings for the SE3-SW5UG-1P-T model.
Instructions for mounting SE3 switches on a DIN rail.
Steps to remove the DIN rail bracket for wall mounting.
Instructions for attaching the wall mounting bracket to the switch.
Provides warnings and details for connecting power to the switches.
Details power input specifications and connection methods.
Details specifications for M12 power connectors.
Explains how to wire the power fault alarm contact.
Provides guidelines for grounding the switches to prevent EMI.
Details RJ45 port specifications, cable requirements, and pin assignments.
Guidelines for connecting fiber optic ports, including TX/RX crossover.
Details specifications for SC and ST fiber port connections.
Instructions on how to check network connectivity using LED indicators after making connections.
Lists general specifications like processing type, MAC addresses, memory buffer, and packet forwarding rate.
Details power specifications for PoE models, including PoE budget and pinout.
Specifies Ethernet compliance standards for RJ45 ports.
Specifies Ethernet compliance standards for M12 ports.
Details specifications for SC/ST fiber ports, including wavelength and distance.
Specifies Ethernet compliance for SFP ports.
Provides dimensional drawings for SE3-SW5U and SE3-SW5U-T models.
Provides dimensional drawings for SE3-SW8U and SE3-SW8U-T models.
Provides dimensional drawings for the SE3-SW5UG-T model.
Provides dimensional drawings for SE3-SW5U-1C1-T and SE3-SW5U-1T1-T models.
Provides dimensional drawings for SE3-SW6U-2C1-T and SE3-SW6U-2T1-T models.
Provides dimensional drawings for the SE3-SW7U-2P-T model.
Provides dimensional drawings for the SE3-SW5UG-1P-T model.
Provides dimensional drawings for the SE3-SW10UG-2P-T model.
Provides dimensional drawings for the SE3-SW16UG-4P-T model.
Provides dimensional drawings for the SE3-SWP1A5U-T model.
Provides dimensional drawings for SE3-SWP2A5U-T and SE3-SWP2A5UG-T models.
Provides dimensional drawings for the SE3-SWP2A7U-2P-T model.
Provides dimensional drawings for the SE3-SW5U-N67-T model.
Troubleshooting steps for power-related issues with the switches.
Troubleshooting steps for copper Ethernet connection problems.
Troubleshooting steps for fiber Ethernet connections and SFP modules.
To Next Page
