Balluff Micropulse BTL5-A series User Manual

1-800-543-8390 • WWW.BALLUFF.COM
8
BTL5-A/C/E/G__-M____-B/Z-S32/KA__
Micropulse Linear Position Transducer
Analog Output-Rod Style
™
7 Teach-in mode
rofelbateulaV
gnitsujdadnani-hcaet
5LTB
vnoisre
.niM
eulav
eulavlluN
)dnedaeh(
rofedoC
gnitsujda
rofedoC
ni-hcaet
eulavdnE
(dnedor)
.xaM
eulav
rorrE
eulav
gnisir
A )tloV(05.0–0 00.2 00.400.01+05.01+05.01+
G )tloV(05.01–00.01– 00.2 00.400.01+05.01+05.01+
B )tloV(52.5–00.5– 00.2 00.400.5+52.5++.552
C )Am(0 0 00.6 00.2100.0202>02>
E )Am(4<00.4 00.6 00.2100.0202>4<
gnillaf
A )tloV(05.01+00.01+ 00.8 00.6005.0–05.0–
G )tloV(05.01+00.01+ 00.8 00.600.01–05.01–05.01–
B )tloV(52.5+00.5+ 00.8 00.600.5–52.5–52.5–
C )Am(02>00.02 00.41 00.80002>
E )Am(02>00.02 00.41 00.800.44<4<
BTL5-A... with magnet in stroke range
10.50
10.00
4.00
5.39
5.39
9.89
5.39
V
V
V
V
V
V
V
10.50
10.50
10.50
V
V
V
>3 s
<1 s
>3 s
>6 s
1
>2 s
0.00
0.00
V
V
>2 s
1
10.00
V
10.00
V
>2 s
3.60
9.15
4.82
4.00
19.13
m A
m A
20.00
20.00
20.00
m A
m A
12.00
m A
4.00
m A
m A
m A
m A
m A
m A
m A
m A
m A
m A
3.60
9.15
9.15
1.04
V
3.60
3.60
1 /2
1 /2
1 + 2
1 + 2
2
<1 s
Current
position value
Code =
Error value
New null
value
New end
value
Code = Null
value
Code = End
value
Code for
Teach-in
Code =
Error value
Current
position value
Current
position value
Current
position value
Current
position value
Code =
Error value
Current
position value
Displayed values (example)
for 0...10 V for 4...20 mA
Code = Error
value
Teach-
in
Enable buttons
End,
disable buttons
Null point End point
Table 7-1: Value table for
teach-in and manual adjust
Enable buttons:
1. Press one of the buttons for at
least 3 s. Release button.
2. Within 1 s hold down buttons
1+2 simultaneously for at least
3 s. Now the Error value
remains stored as the output
signal.
.
Select teach-in:
Hold down button 1 for at least 2 s
until the code for teach-in is
displayed. Release button.
Set nullpoint:
1. Move magnet to exact desired
nullpoint.
2. Hold down button 1 for at least
2 s. The new nullpoint is set.
Set end point:
3. Move magnet to exact desired
end point.
4. Hold down button 2 for at least
2 s. The new end point is set.
End teach-in
and disable buttons:
Hold down buttons 1+2 simulta-
neously for at least 6 s to end the
calibration procedure until the Error
value is displayed. Then press one
of the buttons briefly to disable
both buttons.
Check your new settings
carefully before you start up
the machine or system.
In case of an error or a break
in the activation sequence of
buttons, wait for the duration
of protection time of 12 s
before starting the sequence
anew.
Z_Analog_122003.pmd 12/11/2003, 3:47 PM8

Balluff Micropulse BTL5-A series Specifications

General

Brand	Balluff
Model	Micropulse BTL5-A series
Category	Transducer
Language	English