Table of contents
TABLE OF CON TENTS
1. Safety................................................................................................................. 3
1.1 General considerations............................................................................................................... 3
1.2 Important safety instructions ......................................................................................................... 4
2. General............................................................................................................... 7
2.1 Installation requirements . . ........................................................................................................... 7
2.2 Unpacking the projector .............................................................................................................. 8
2.3 Initial inspection......................................................................................................................10
2.4 Installation process overview........................................................................................................ 11
3. Physical installation ..............................................................................................13
3.1 Positioning the DP2K C-series projector at port window........................................................................... 13
3.2 Installation of the exhaust system . .................................................................................................. 15
3.3 Connecting the projector with the power net .......................................................................................16
3.4 Power loop through to the projector electronics ....................................................................................18
3.5 Connecting a UP S with the pro jector electronics...................................................................................19
4. Lamp & Lamp House .............................................................................................21
4.1 Introduction ..........................................................................................................................21
4.2 Removal of the lamp house .........................................................................................................23
4.3 Removal of the xenon lamp ......................................................................................................... 24
4.4 Installation of the Xenon lamp.......................................................................................................28
4.5 Installation of the lamp house ....................................................................................................... 33
4.6 Resetting the lamp parameters . .. ..................................................................................................34
4.7 Realignment of the lamp in its refl ector.............................................................................................35
5. Lenses & lens holder .............................................................................................37
5.1 Available lenses .....................................................................................................................37
5.2 Lens selection .......................................................................................................................38
5.3 Lens removal ........................................................................................................................ 39
5.4 Lens installation .....................................................................................................................40
5.5 Lens shift, zoom & focus . .. .........................................................................................................42
5.6 Scheimpflug adjustment.............................................................................................................42
6. Input & communication ..........................................................................................47
6.1 Introduction ..........................................................................................................................47
6.2 Local keypad of the DP2K C-series projector ......................................................................................48
6.3 Communication ports of the D P2K C-series projector . . ........................................................................... 49
6.4 Source input ports of the DP2 K C-series projector.................................................................................50
6.5 LED indications on the Integrated Cinem a Processor m odule. ....................................................................51
7. Communicator touch panel......................................................................................53
7.1 Introduction ..........................................................................................................................53
7.2 Installing the touch panel interface..................................................................................................54
7.3 Reposition the touch pane l interface................................................................................................55
8. Starting up..........................................................................................................57
8.1 Switching ON the DP2K C-series projector.........................................................................................57
8.2 Switching OFF the DP2K C-series projector ....................................................................................... 57
9. Projector registration.............................................................................................59
9.1 Introduction ..........................................................................................................................59
9.2 Download the certificate file.........................................................................................................59
9.3 Registration of new projector........................................................................................................60
9.4 Update registration of an existing projector . ........................................................................................65
10. Removal and installation of projector covers................................................................67
10.1 Removal of the lamp cover..........................................................................................................67
10.2 Removal of the input cover. .........................................................................................................68
10.3 Removal of the front cover .......................................................................................................... 69
10.4 Removal of the side cover........................................................................................................... 70
10.5 Removal of the rear cover...........................................................................................................70
10.6 Removal of the top cover............................................................................................................71
10.7 Open the sealed com partment ......................................................................................................72
10.8 Close the sealed compartment......................................................................................................73
10.9 Installation of the top cover.......................................................................................................... 74
10.10 Installation of the rear cover......................................................................................................... 75
10.11 Installation of the side cover ........................................................................................................76
10.12 Installation of the front cover ........................................................................................................76
10.13 Installation of the input c over........................................................................................................77
11. Maintenance........................................................................................................79
11.1 Removing the front dust filter........................................................................................................ 79
11.2 Clean the dust filter on the bottom side.............................................................................................81
R5905050 DP2K C-SERIES 10/07/2012
1
To Next Page
Loading...
