Barco HDX W18 - 16.6 Removal of the Lamp Cover

To Next Page

To Previous Page

16. Servicing

Image 16-9

Mount dust ring

4. Mount lens again.

16.6 Removal of the lamp cover

WARNING: Switch off the projector and unplug the power cord before starting the procedure.

Necessary tools

7mmﬂat screw driver

How to remove

1. Release the 6 captive screws.

R5905032 HDX SERIES 20/11/2014

299

Main Page

Default Chapter5
- Table of Contents5
1 Safety11
- General Considerations11
  - General Safety Instructions11
  - Notice on Safety11
- Important Safety Instructions12
- Important Warnings Concerning HDX Flight Cases14
2 General17
- Installation Requirements17
- Projector Weight18
- Unpacking the Projector18
- Initial Inspection19
- Box Content19
- HDX Flight Case20
- Projector Conﬁgurations20
  - Rear Projection21
  - Positioning the Projector22
- Projector Air Inlets and Outlets24
- Free Download of Projector Toolset24
- Installation Process Overview25
- Quick Setup25
3 Physical Installation27
- Remote Control Unit (RCU)27
- Lenses31
- Connecting the Projector with the Power Net42
- Alignment of a Table Mounted Projector43
- Mounting the Bottom Carry Handler43
- Mounting the Top Carry Handler45
- Suspension of the Projector with Rigging Clamps46
- Alignment of a Ceiling Mounted Projector48
4 Input & Communication51
- Introduction51
- Input Source Connections52
- Communication Connections54
- Utility-Accessory Outlet57
5 Getting Started59
- RCU & Local Keypad59
- Terminology Overview59
- Power on Projector61
- Software Overview63
- Switching to Standby64
- Power off Projector64
- Status Leds65
- Using the RCU65
- Projector Address67
- Source Selection67
6 Quick Set up Adjustment69
- Text Boxes on or off69
- Quick Lens Adjustment Via LENS Key69
- Direct Lens Adjustment (RCU)71
- Quick Picture in Picture72
- Quick Language Selection72
7 Start up of the Adjustment Mode75
- About the Adjustment Mode75
- About the Use of the Remote Control and the Local Keypad75
- Start up the Adjustment Mode75
- Navigation and Adjustments76
- Menu Memory77
- Shortcut Keys to the Menus77
- Test Patterns in Adjustment Mode78
- Help Information in Adjustment Mode78
8 Input79
- Input Menu Overview79
- Input Selection80
- Advanced Settings81
- Input Locking85
- Minimum Delay86
- Native Resolution87
- No Signal88
- Edid92
- Input97
9 Image109
- Image Menu Overview109
- Start up the Image Adjustments110
- Image Settings110
- Aspect Ratio122
- Timings124
  - Source Timings124
  - Advanced Timings, Clamp Delay - Clamp Width125
- Image File Services127
- Save Custom Settings135
- What Can be Done135
- Splash Image136
10 Layout139
- Layout Menu Overview139
- Introduction139
- Main Window140
- Pip Window143
- Layout File Services149
- Lens Behavior154
11 Lamp157
- Lamp Menu Overview157
- Lamp Power Mode157
- Hush Kit Activate/Deactivate158
- Lamp Power159
- Auto Dimming When on Pause160
- Auto Dimming When no Signal161
- Auto Dimming When Over-Temperature162
- CLO Mode (Constant Light Output Mode)163
- CLO Targets165
- LPS Power165
- How to Display166
- Lamp Identiﬁcation166
- Z-Axis Adjustment167
12 Alignment169
- Alignment Menu Overview169
- Orientation170
- Lens Adjustment, Zoom - Focus171
- Lens Adjustment, Shift172
- Lens Adjustment, MID Position173
- Calbrate Lens at Startup174
- Calibrate Lens174
- Warping175
- Blanking Adjustment198
- Contrast-Intensity200
- Gamma201
- Internal Patterns201
- Color Space203
- What Can be Adjusted203
- Scenergix205
- Glasses217
13 Projector Control223
- Projector Control Menu Overview223
- Individual Projector Address224
- Projector Common Address225
- Serial Communication226
  - Baud Rate Setup226
  - Interface Standard226
- Network227
- IR Control Switching241
- DMX242
- Buttons252
  - Standby Button252
  - Shortcut Keys253
- Menu Position254
- Local LCD254
- Language Selection255
- Scheduler256
- GSM Conﬁguration, Activation263
- GSM Conﬁguration, Subscription265
- FLEX, Light Output Conﬁguration267
- SMS Services269
14 Service271
- Service Menu Overview271
- Identiﬁcation272
- What Can be Seen272
- Diagnosis273
- Internal Service Patterns281
- Convergence285
- Factory Defaults286
- USB Memory287
- Reset Formatter289
- Reﬁll Mode289
- Save Custom Settings290
- Special HD Camera Mode291
- Auto Dimming When Over-Temperature292
- Time and Date293
15 Maintenance295
- Cleaning the Lens295
- Cleaning the Exterior of the Projector295
16 Servicing297
- Inserting an Input Module297
- Removal of the Lamp House298
- Installation of the Lamp House299
- Removal of the300
- Mounting the302
- Removal of the Lamp Cover303
- Mounting the Lamp Cover304
- Replacement of the High Density Dust Filter305
- Remove and Clear Metal Front Filter306
- How to Install307
Dimensions309
- Dimensions of a HDX Projector309
Speciﬁcations311
- Speciﬁcations of the HDX W12311
- Speciﬁcations of the HDX W14312
- Speciﬁcations of the HDX W18313
- Speciﬁcations of the HDX W20 FLEX314
Standard Source Files317
- Table Overview317
DMX Chart321
- DMX Chart, Basic321
- DMX Chart, Full321
- DMX Chart, Extended322
Stacking HDX Projectors325
- Mount Stacking Points325
- Aligning Stacked HDX Projectors328
Environmental Information331
- Disposal Information331
- Rohs Compliance331
- Production Address333
Index335

Barco HDX W18 - 16.6 Removal of the Lamp Cover

Table of Contents

Related product manuals