EasyManua.ls Logo

Basler DECS-250 - Page 218

Basler DECS-250
374 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
26-2 9440300990
Testing DECS-250
With the RTM Analysis screen controls, you can:
• Select the parameters to be graphed
• Adjust the resolution of the graph x axis and the range of the graph y axis
• Start and stop plot captures
• Open an existing graph file, save a captured plot in a graph file, and print a captured graph
Graph Parameters
Any four of the following parameters may be selected for plotting in the graph areas.
• APC Error to PI
• APC Integrator state
• APC PI output
• Auxiliary voltage input (Vaux)
• Average line current (Iavg)
• Average line-to-line voltage (Vavg)
• AVR error signal (Errln)
• AVR output
• Bus frequency (B Hz)
• Bus voltage (Vbus)
• Compensated frequency deviation
(CompF)
• Control output (CntOp)
• Cross-current input (Iaux)
• Desired APC Reference
• Droop
• FCR error
• FCR state
• FCR output
• Field current (Ifd)
• Field voltage (Vfd)
• Filtered mechanical power (MechP)
• Final PSS output (Pout)
• Frequency response signal (Test)
• FVR error
• FVR state
• FVR output
• Generator frequency (G Hz)
• Grid connect state
• Grid code test signal
• Internal state (TrnOp)
• Lead-lag #1 (x15)
• Lead-lag #2 (x16)
• Lead-lag #3 (x17)
• Lead-lag #4 (x31)
• LVRT Desired var Reference
• LVRT var Reference
• Mechanical power (x10)
• Mechanical power (x11)
• Mechanical power (x7)
• Mechanical power (x8)
• Mechanical power (x9)
• Negative sequence current (I2)
• Negative sequence voltage (V2)
• Network Load Share
• Null Balance Level (Null Balance)
• Null Balance State (Null State)
• OEL controller output (OelOutput)
• OEL reference
• OEL state
• Phase A current (Ia)
• Phase A to B, line-to-line voltage (Vab)
• Phase B current (Ib)
• Phase B to C, line-to-line voltage (Vbc)
• Phase C current (Ic)
• Phase C to A, line-to-line voltage Vca
• Position Indication (PositionInd)
• Positive sequence current (I1)
• Positive sequence voltage (V1)
• Post-limit output (Post)
• Power factor (PF)
• Power HP #1 (x5)
• Pre-limit output (Prelim)
• PSS electrical power (PSSkW)
• PSS terminal voltage (Vtmag)
• Reactive power (kvar)
• Real power (kW)
• SCL controller output (SclOutput)
• SCL reference
• SCL state
• SCL PF reference
• Speed HP #1 (x2)
• Synthesized speed (Synth)
• Terminal frequency deviation (TermF)
• Time response signal (Ptest)
• Torsional filter #1 (Tflt1)
• Torsional filter #2 (x29)
• Total power (kVA)
• UEL controller output (UelOutput)
• UEL reference
• UEL state
• Var limiter output (VArLimOutput)
• Var limiter reference
• Var limiter state
• Var/PF error
• Var/PF state
• Var/PF output
• Washed out power (WashP)
• Washed out speed (WashW)