baxter OV500 Series User Manual

– 18 –
Setup Guide
SETUP
NUMBER
SETUP ITEM DISPLAY
P0 Network Number RS485 network number, default is 1.
P1 Maximum Temperature
Setpoint
This is the maximum temperature at which the oven can be set. Range is
50°F to 525°F (10°C to 275°C). Default is 525°F.
P2 Preheat Temperature This is the default temperature setpoint when the oven is rst turned on
(Program 0). The preheat temperature cannot be set higher than the value
in P1 or lower than the value in P3.
Range is 50°F to 525°F (10°C to 275°C). Default is 375°F.
P3 Minimum Temperature
Setpoint
This is the minimum temperature at which the oven can be set. Range is
50°F to 200°F (10°C to 93°C). Default is 50°F.
P4 Temperature O󰀨set This value permits an o󰀨set of correction between the oven temperature
display and the real baking chamber temperature. Call your authorized
service agency for help with this feature. Default is 0.
P5 Heat OFF O󰀨set This value adjusts the temperature di󰀨erence between the set point and
stopping of the heating system. Call your authorized service agency for
help with this feature. Default is -2.
P6 Heat Di󰀨erence
Hysteresis
This value adjusts the temperature di󰀨erence between the on temperature
and o󰀨 temperature of the heating system. Call your authorized service
agency for help with this feature. Default is 4.
P7 Maximum Steam Time Time set is the maximum time (in seconds) that water is supplied during the
STEAM TIMER operation.
Maximum duration time for bake steam mode is 30 seconds of continual
steam.
Maximum duration time for bake steam pulse mode is 60 seconds of 5
second pulses of steam.
Default is 20.
P8 Temperature Units The oven can be set to display temperature in Fahrenheit or Celsius. To
ensure accurate temperature parameters, call your authorized Baxter
service o󰀩ce for help with this feature. Default is F.
P9 Timer Mode The TIMER can be set up to display minutes set/minutes remaining or
hours and minutes. Select 0 for minutes set/minutes remaining or 1 for
hours and minutes. (If this parameter is changed to hours and minutes,
a label has been provided to place on the control panel to indicate the
change.) Default is 0.
P10 Vent Evacuate Time Time set is the time (in seconds) that the vent is 100% open at the
beginning of the venting cycle. Range is 0 to 180 seconds. Default is 90.
P11 Vent Open Percentage This value is the percentage the bake chamber vent is open after the vent
evacuate time has expired. Range is 5 to 100%. Default is 50.
P12 End of Bake Automatic
Vent - Enable
This feature enables the Automatic Vent Cycle. Select 0 to disable or 1 to
enable this feature (see P13 for entering time). Default is 1.
P13 End of Bake Automatic
Vent Time
This is the number of minutes before the end of the bake cycle that the vent
is open. Default is 1.
P14 Steam Timer Mode The steam timer can be set up to display in seconds or operate in food
service mode. Select 0 for seconds or 300 to 990 for food service mode.
Default is 0.
P15 Interior Light Brightness This value is the brightness of the interior lights. The higher the number, the
brighter the lights. Range is 50 to 100. Default is 90.
P16 Clock Operation This selects either 12 hours (AM/PM) or 24 hours real time display. Press
the Bake Time Up button to switch between the two types of display.
AP = 12 Hour Clock [Default]
24 = 24 Hour Clock

baxter OV500 Series Specifications

General

Brand	baxter
Model	OV500 Series
Category	Oven
Language	English