To Next PageTo Next PageWhat does it mean if my Binder FD 56 chamber is without function, and the standby icon is displayed?
The chamber is likely in standby mode. Press down the standby button until the display lights up.
What to do if there is an electrical hazard during live maintenance work on Binder Accessories?
To avoid electrical hazards during maintenance on your Binder Accessories, ensure the chamber remains dry, never remove the rear panel, and always disconnect the chamber from power by turning off the main switch (for ED, FD, FED size 720 models) and pulling the plug. It is essential that only licensed electricians or experts authorized by BINDER perform any maintenance work.
How to fix a Binder FD 56 Laboratory Equipment fan that doesn’t turn or turns too slowly?
If you have a BF or FED model, the fan speed might be set too low; set the fan speed to 100%. If the problem persists, further assistance is needed.
What does the alarm message “!TProt” mean on my BD or BF Binder FD 56 Laboratory Equipment?
The safety device class 3.1 has responded. Check the settings of the temperature set-point and of the safety device class 3.1.
Why are there deviations from the indicated heating-up times in my Binder Laboratory Equipment?
The chamber might be fully loaded. Try loading the chamber with fewer items or consider allowing longer heating-up times.
What to do if the Binder FD 56 Laboratory Equipment chamber has no function and the standby icon is displayed?
The chamber is likely in standby mode. Press down the standby button until the display lights up.
Qualification requirements for chamber installation, testing, and operation.
Importance of the manual, safety instructions, and future reference.
Definitions of DANGER, WARNING, CAUTION, and NOTICE signal words.
Use of the safety alert symbol to indicate risk of injury.
Information and indications found on the chamber's type plate.
Local/national regulations, authorized accessories, and ventilation advice.
Approved uses and limitations of the chamber.
List of practices considered improper use, posing risks despite safety features.
Unavoidable risks during operation and measures to minimize them.
Description of the controller display, buttons, and USB interface.
Instructions for safe handling, lifting, and securing the chamber during transport.
Details on power supply requirements, cables, and fuses for various models.
How to set target temperature and fan speed values.
Function of the safety device and cut-off temperatures for different models.
Explanation of safety controller classes (limiter/protection) and their functions.
How to set the limit temperature for the safety controller.
How alarms are displayed and actions to take during an alarm.
Steps to set run-time and fan operation after timer expiry.
How to stop or modify timer settings while running or after expiry.
Setting run-time, fan speed, and temperature set-point for temp-dependent timers.
How to stop or modify temp-dependent timer settings.
Setting run-time and fan speed for delayed ON timer.
How to modify timer settings for delayed ON timer.
Settings for networking via Ethernet, including MAC address, IP, subnet, gateway.
Recommended maintenance schedule and service procedures.
Basic troubleshooting steps for common chamber issues.
Qualification requirements for chamber installation, testing, and operation.
Importance of the manual, safety instructions, and future reference.
Definitions of DANGER, WARNING, CAUTION, and NOTICE signal words.
Use of the safety alert symbol to indicate risk of injury.
Information and indications found on the chamber's type plate.
Local/national regulations, authorized accessories, and ventilation advice.
Approved uses and limitations of the chamber.
List of practices considered improper use, posing risks despite safety features.
Unavoidable risks during operation and measures to minimize them.
Description of the controller display, buttons, and USB interface.
Instructions for safe handling, lifting, and securing the chamber during transport.
Details on power supply requirements, cables, and fuses for various models.
How to set target temperature and fan speed values.
Function of the safety device and cut-off temperatures for different models.
Explanation of safety controller classes (limiter/protection) and their functions.
How to set the limit temperature for the safety controller.
How alarms are displayed and actions to take during an alarm.
Steps to set run-time and fan operation after timer expiry.
How to stop or modify timer settings while running or after expiry.
Setting run-time, fan speed, and temperature set-point for temp-dependent timers.
How to stop or modify temp-dependent timer settings.
Setting run-time and fan speed for delayed ON timer.
How to modify timer settings for delayed ON timer.
Settings for networking via Ethernet, including MAC address, IP, subnet, gateway.
Recommended maintenance schedule and service procedures.
Basic troubleshooting steps for common chamber issues.
General| Brand | Binder |
|---|---|
| Model | FD 56 |
| Category | Laboratory Equipment |
| Language | English |
