INSTRUCTIONS FOR USE
Manual operation
Programming the oven may not be necessary In this case however turn programmer
adjusting ring
C
clockwise unt~l symbol
$
coinc~des w~th dial
E
When
adjusting
the timer. check to make sure that the hour set on the timer is synchronl-
zed with the hour set on dial F (fly.
15).
Semiautomatic operation of the oven
Manual cooking start programmed cooking stop
preset the food to be cooked
turn adjusting ring
C
clockw~se and preset the required cooking time on dial
E.
turn the thermostat knob unt~l the required temperature is reached and turn the selector
knob on the operating funct~on.
When the cooking time is over a continuous acoustic signal warns to blow off the oven.
(To cut off this signal, turn adjusting ring
C
clockwise, until symbol
0
coincides with.the
Index of dial
E).
Automatic operation of the oven
-
Prepare the food to be cooked
Press and turn knob B clockwise, until the required cooking start time is preset on dial
F
Turn adjusting rlng
C
clockwise, until the time selected for stopping cooking is preset on
dial
F
Turn the thermostat knob to reach the required temperature value and the temperature
of the selector for the functions.
At the end of the cooking time a continuous acoustic signal warns-to blow off the oven
(To cut
ofl this signal, turn adjusting ring
C
clockwise, until symbol
coincides with the
index of dial
E).
Important
To cut ofl the programmed cooking time and to blow off the oven before the preset time,
turn adjusting
rlng
C
clockwise, until symbol
"0
is displayed on dial
E.
Then put off the
acoustic signal as descr~bed above.
If cooking must be completed manually, turn adjusting ring
C
clockwise, until symbol
$
appears on dial
E.
Timing may be programmed up to 12 hours in advance. (Ex: the number
8
is used to indi-
cate both
8
a.m. and
8
pm). Hence cooking can only be programmed 12 hours ahead
maximum.
The
automatc cooking does not present any difference from the manual cooking, as in this
last case, the cooking time is preset by the programmer.
For automatic cooking it is preferable to use foods which do not require special care.
INSTRUCTIONS FOR USE
INSTRUCTIONS FOR
THE
1
[
A
ELECTRONIC PROGRAMMER
Setting the actual hour
n
"
+
Once the electric connection 1s over, the
nnnnnn
display flashes and shows 0.00. Press
keys (1) and (2) at the same time, and
set the actual time by
pressmg keys
(-)
and
(+)
w~thin
4
seconds The oven
1234
General remarks
remains in manual operation and can be
used without any programming.
Between 10 p.m. hours and
6
a.m. hours the display intensity is automatically dimmed.
If the acoustic signaller is not disconnected (as per subsequent instructions), it is cut off
after
2
minutes.
Any programming described hereunder is activated after approx.
4
seconds from the pre-
setting.
+
23
hours and
59
minutes is the maximum oroarammed time.
.
Any and all programmed settings are erased when the voltage lacks. When the voltage
is cut in again, the display flashes and shows 0.00. To reset the equipment operation
preset both the actual time and the programme again.
Acoustic minute counter
When this device is used as a simple acoustic signaller, press key (I) and programme the
required time by pressing keys
(-)
and (+)within the next
4
seconds: the actual time reap-
pears and symbol
(6)
is activated. Press one of the keys from
1
to
4
to disconnect the
acoustic signaller. Also symbol (6) is deactivated.
Setting
the end
of
the
cooking
time
To start the cooking process immediately and to automatically preset the time, operate as
foilows:
Select the required function and temperature using the selector of the functions and
the thermostat.
.
Press key
(2)
and set the cooking time by pressing keys
(-)
and
(+)
within the next
4
seconds. The actual time reappears and pilot lights (A) and (AUTO) remain
ON.
The
cooking time left can be controlled by pressing key (2), or the time can be changed
by
repeating the same procedure.
To Next Page
Loading...
Need help?
General
