2.3 MANUFACTURER’S NOTE
The In-plant LFT Lift Table equipment has been carefully inspected and tested at the manufacturer’s plant prior to shipment, but MUST be
checked upon receipt for transport damage. Any observed transport damage is to be listed on the signed copy of the freight document.
There are many configurations or custom designs whose specifications may not be fully reflected in this manual. Contact your Blue Giant
Dealer to obtain the General Arrangement drawing for application specific designs.
Notify the freight forwarder and the dealer of any damage WITHIN 24 HOURS.
2.4 OWNER’S RESPONSIBILITY
The In-plant LFT Lift Table equipment needs to be maintained and inspected by the owner to verify its safe condition for operation.
1. The owner should recognize the inherent danger of the interface between the In-plant LFT Lift Table equipment and other components.
The owner should, therefore, train and instruct operators in the safe use of the In-plant LFT Lift Table equipment and accessories in
accordance with the manufacturer’s recommendations.
2. The owner should thoroughly familiarize themselves with the following procedures and specifications as referenced in this manual, and
request immediate replacement of all manufacturer-supplied documents that are missing, damaged, or otherwise illegible. Owners
shall apply sound principles of safety, training, inspection, maintenance, and expected operating environment toward their In-plant
LFT Lift Table equipment usage and maintenance requirements.
• Commissioning instructions
• Operating instructions
• Daily maintenance procedures checklist
• Inspections procedures
• Recommended spare parts lists
Upon receipt of any newly purchased In-plant LFT Lift Table equipment, the owner shall verify the presence of owner’s manuals, oper-
ating placards, and any other documentation necessary for training dock personnel how to use the equipment safely and effectively.
3. All Blue Giant In-plant LFT Lift Table equipment shall undergo regularly scheduled planned maintenance. Maintenance requirements
will vary according to usage frequency and application, so the owner shall contact with their authorized Blue Giant distributor for
schedule recommendation. Written records of the performance of these procedures shall be kept as per warranty requirements and
per local state or provincial requirements. Please see”7.0 MAINTENANCE” on page 15.
4. In-Plant Lift Table equipment that is structurally damaged, experiencing performance irregularities, or has been potentially
compromised shall be removed from service until a trained and authorized manufacturer’s representative can conduct an inspection
and perform any necessary repairs.
5. As with any piece of machinery, In-plant LFT Lift Table equipment requires routine maintenance, lubrication, and adjustments.
Recommended procedures are itemized in the Planned Maintenance Program (PMP) checklist included in installation and technical
manuals. It is recommended that for anything other than the basic maintenance procedures outlined in this manual, please contact
your Blue Giant Dealer.
6. The owner shall ensure that all nameplates and safety labels are in place and legible, and that the appropriate manuals are provided to
authorized users. Replacement nameplates, safety labels, and manuals are available through the Blue Giant Aftermarket Department.
See “12.0 DECAL IDENTIFICATION AND LOCATION” on page 45 in this manual for more information.
7. Unless specifically agreed to in writing by Blue Giant Equipment Corporation at the time of order (and prior to manufacture), all Blue
Giant In-plant LFT Lift Table equipment is sold as a complete offering and must not be altered or added to in any manner (which
includes configuration and function) without written permission from an authorized manufacturer’s representative. These changes
shall also satisfy all safety recommendations of the original equipment manufacturer for the particular application of the In-plant
LFT Lift Table equipment.
8. If, at the request of the owner, Blue Giant does not supply all or some of the In-plant LFT Lift Table equipment power unit and/or control
panel components, the owner shall assume responsibility for any and all operational and safety issues associated with the resulting
configuration.
9. The owner must adhere to the load classification information provided on the product nameplate. Failure to do so will void product
warranty and can result in serious injury, including death.
10. Operational placard must be visible from equipment location and permanently attached to a wall or structure.
11. The owner shall ensure that inspections are performed to the lifting device as prescribed by law or regulation.
IN-PLANT LFT LIFT TABLE — OWNER'S MANUAL
7ISSUE DATE: NOVEMBER 15, 2023 REV. 1.0 (PART # 038-475E)
To Next Page
Loading...
