What to do if my Bosch Digital Camera reboots frequently or intermittently?
If your Bosch Digital Camera reboots frequently or intermittently, test it with another power supply. You can also check the Bosch website for a software update that might address the issue.
Why is the picture dark on my Bosch Digital Camera?
If the picture from your Bosch Digital Camera is dark, check that the Gain Control is set to High, and the Auto Iris Level is set to the appropriate level. Also, ensure that the maximum distance between any two Ethernet connections is 100 m (328 ft) or less. You may also want to restore all camera settings.
What to do if there is no video on my Bosch Security Camera?
If your Bosch Security Camera is not showing any video, first ensure that the main power to the power supply is switched on. If you have a web page, try cycling the camera's power off and on. If you do not have a web page, use Configuration Manager to identify the correct IP address. Also, verify that there is 24 V output from the transformer and check the integrity of all wires and connectors connected to the camera.
What to do if my Bosch Digital Camera moves when attempting to move other cameras?
If your Bosch Digital Camera moves when you're trying to move other cameras, check that the camera’s IP address is properly set. Use Configuration Manager to confirm that two cameras do not have the same IP address. If they do, change the address of one of the cameras.
Why is there no video on my Bosch Digital Camera?
If there is no video from your Bosch Digital Camera, first, check that the main power to the power supply is on. If you have a web page, cycle the camera's power off and on. Use Configuration Manager to identify the correct IP address. Verify that there is 24 V output from the transformer and check the integrity of all wires and mating connectors to the camera.
Why is there no network connection for my Bosch Digital Camera?
If your Bosch Digital Camera has no network connection, verify all network connections. Also, ensure that the maximum distance between any two Ethernet connections does not exceed 100 m (328 ft). If you're using a firewall, check that the Video Transmission mode is set to UDP.
How to fix a background that is too bright on a Bosch Security Camera?
If the background is too bright on your Bosch Security Camera, turn on backlight compensation.
How to fix no camera control on Bosch Security Camera?
To resolve the issue of no camera control on your Bosch Security Camera, ensure that the LAN cable has a secure and good connection. Refresh the browser and ensure that video is updated. You can also cycle the camera's power off and on.
Why does my Bosch Security Camera move when I try to move other cameras?
To resolve the issue of a Bosch Security Camera moving when attempting to move other cameras, check that the camera’s IP address is properly set. If the camera’s IP address is not set, use Configuration Manager to confirm that two cameras do not have the same IP address. If they do, change the address of one of the cameras.
What to do if Bosch Security Camera not working after cold?
If your Bosch Security Camera does not operate at all, or does not operate as expected, after being subjected to extremely low temperatures (below -40 ° (-40 °F)), allow the camera to warm up for 60 minutes before attempting PTZ operations. If it still does not operate after this warm-up period, reset the camera by typing “/reset” at the end of the camera's IP address in your web browser.
General| Low-light Performance | Starlight technology |
|---|---|
| Ingress Protection | IP66 |
| IK Rating | IK10 |
| Sensor Type | 1/2.8-inch CMOS |
| Video Compression | H.265, H.264, MJPEG |
| Lens Type | Varifocal |
| Frame Rate | Up to 60 fps |
| Vandal Resistance | IK10 |
| Optical Zoom | 30x |
| Operating Temperature | -40 °C to +60 °C (-40 °F to +140 °F) |
| Power | PoE+ (IEEE 802.3at) |
| Aperture | F1.6 to F4.7 |
| Day/Night | True Day/Night |
| Audio | 2-way audio |
| Network Interface | 10/100 Base-T Ethernet |
| Power Supply | 24 VAC; High PoE (IEEE 802.3at, Class 4) |
| Focal Length | 4.3 mm to 129 mm |
Details the hardware and software prerequisites for camera operation.
Guides on setting up network connectivity and IP addressing for the camera.
Explains security measures for accessing the camera, including initial password setup.
Provides access to core camera settings like sensor mode, image rotation, and LEDs.
Adapts video data transmission settings for different network environments.
Covers configuration of storage media, including iSCSI and local SD cards.
Configures how the camera responds to alarms, including IP address connections.
Identifies common problems and provides actions to resolve them.
Explains how to perform a hardware reset for various troubleshooting scenarios.
To Next Page