Bosch CC 100 M - Symbol tables (PIC 200 PG4)

(§> BOSCH
Flexible Automation
Description Stage 4 Chapter 1
Symbol tables (PlC 200 • PG4)
Address
Symbol Comment
E 0.0 CCRESETO Control Reset output
E 0.1
CCIPOSAL Axis INPOS
E
0.2 CCSPIPOS Spindle INl'OS
E
0.3 CCELAUFT E axis running
E 0.4
CCPROGAK Programing running
E
0.5 CCDRYRUN Test without movement (dry run)
E
O.S CCOPCEIN Online PlC/PC
E 0.7
CCDNCAKT
ONC_Mode
E
1.0
CCSTARTO
Start key (NO contact)
E 1.1
CCSTOPOO Stop key (NC contact)
E 1.2 CCBCDOIT BCD_Acknowledgment
E 1.3
CCPROMEM Program stored
E
1.4 CCEINAKT Re-entry cycle active
E
1.5
CCDNCSTR ONC start
E
I.S CCDNCRST ONC RESET
E 1.7
CCDNCSTP
ONC STOP transverse
E
2.0 CCWMHTSl
MTB_key 1
E
2.1 CCWMHTS2 MTB_key 2
E 2.2
CCWMHTS3
MTB_key3
E
2.3 CCWMHTS4 MTB_key4
E 2.4
CCWMHTS5
MTB_key5
E 2.5
CCWMHTSG
MTB_keyS
E
2.S
CCWMHTS7
MTB_key 7
E
2.7
CCWMHTSS MTB_key8
E 3.0
CCBCAAOl
BCD-output bus address 1
E 3.1
CCBCAA02 BCD-output bus address 2
E
3.2 CCBCAA04 BCD-output bus address 4
E
3.3 CCBCAAOS BCD-output bus address 8
E 3.4
CCBCAA10 BCD-output bus address 10
E
3.5
CCBCAA20 BCD-output bus address 20
E 3.S
CCBCAA40
BCD-output bus address 40
E
3.7 CCBCASTB Data valid (Strobe)
E 4.0
CCBCADOl BCD-output
bus data 1
E
4.1
CCBCAD02 BCD-output bus data 2
E
4.2 CCBCAD04 BCD-output bus data 4
E 4.3
CCBCADOS BCD-output bus data 8
E
4.4 CCBCAD10 BCD-output bus data 10
E
4.5 CCBCAD20 BCD-output bus data 20
E
4.S
CCBCAD40 BCD-output bus data 40
E
4.7
CCBCADSO BCD-output bus data SO
E
5.0 CCEILJOG GO or jog in rapid traverse
E
5.1 CCINPOSX
X axis in pas
E
5.2
CCINPOSY Y axis in pes
E 5.3
CCINPOSZ Z axis in pas
E
5.4 CCINPOSE E axis in pas
Address Symbol
Comment
A
0.0 CCENDSOP
Limit switch + transverse
A
0.1 CCENDSON
Umit switch - transverse
A
0.2 CCREFPXO
Reference point X transverse
A 0.3
CCREFPYO Reference point Y transverse
A 0.4
CCREFPZO
Referee point Z transverse
1 -37
CC lOOM
User Manual
Type
Type
www.DaltonsWadkin.com
www.DaltonsWadkin.com
www.DaltonsWadkin.com