Operation
Climate 2000 – 6721852026 (2024/05)
28
Heat mode
▶ Press and hold the Mode key until appears on the display.
▶ Set the required temperature with the . and / keys.
▶ Press the key until the required air speed is reached.
If the outside temperature is very low, the heating capacity of the air
conditioning system may not be sufficient. We recommend connecting
additional heat sources.
3.5 Setting timer
ON and OFF timers can be set to between 0 and 24 hours, in 30-minute
increments for the first 10 hours, then in 1-hour increments. If 0 hours
is set, the timer is cancelled.
Setting the on timer
▶ Press the key until the symbol appears.
▶ Press the . or / key to set the desired time.
The setting is applied shortly afterwards.
Setting the off timer
▶ Press the key until the symbol appears.
▶ Press the . or / key to set the desired time.
The setting is applied shortly afterwards.
Cancelling timer
▶ Press the key to select the corresponding timer.
▶ Set 0.0 hours.
The timer is cancelled after a short time.
Combining timers
The two timers can be set at the same time. Either timer can be
programmed to activate prior to the other
▶ Set the on timer and off timer.
The settings will be automatically combined.
Table 26 Example
You can not program the on timer and off timer to operate the unit at
different temperatures or with other settings.
3.6 Other functions
3.6.1 Setting the swing function
NOTICE
If the louvre remains at the lowest position during cooling mode for an
extended period, condensate may be discharged. Adjusting the louvres
vertically by hand may cause faults.
▶ Only use the remote control to adjust the louvres vertically.
Swinging horizontally (left/right)
The horizontal position must be set by hand.
▶ Switch off the indoor unit and disconnect the power supply.
▶ Flip down the air baffle ( Fig. 2).
▶ Swivel the louvres horizontally by hand into the required position.
▶ Put the air baffle back in the original position.
Automatic vertical Swing mode (up/down)
▶ Press the Swing key for longer than 2 seconds to activate the
automatic vertical Swing mode.
The remote control displays the symbol .
▶ To cancel the automatic vertical Swing mode: press the Swing key
again.
Cleaning position
To make cleaning easier, the louvre can be brought into a special
position (depending on product type).
▶ Press the Mode and Swing keys simultaneously for one second when
the device is switched off.
▶ To exit the cleaning position: press and hold both keys again.
3.6.2 Changing over display and alarm buzzer (Mute Mode)
▶ To switch on or off the display at the indoor unit and the alarm buzzer:
press LED key.
▶ To display the current room temperature, press the LED key and hold
for 5 seconds.
▶ To display the set temperature: press and hold the LED key for
another 5 seconds.
3.6.3 Noise reduction (Silent Mode)
This function reduces the noises emitted by the indoor and outdoor unit
when it is in operation. This is particularly advantageous at night, if you
need to show consideration for your neighbours.
▶ During operation, press the key for 2 seconds.
Exiting the function:
▶ Press the key again for 2 seconds.
-or-
▶ Press the K key, Mode key, Turbo key or Clean key.
When the outdoor unit is in quiet mode, it may not be possible to achieve
the required cooling/heating capacity because the compressor operates
at a low frequency.
3.6.4 Restore function
The indoor unit notes the current and previous setting, for e.g. operation
mode, temperature and fan speed. The restore function can switch
between the previous and current setting.
▶ Press the key to switch to the previous setting.
▶ Hold the key pressed for longer than two seconds to switch to the
current setting.
3.6.5 Turbo cool/Turbo heat
When Turbo cool/Turbo heat is active, the indoor unit operates at
maximum power to heat or cool the room quickly.
▶ Turbo cool: switch on Cooling mode and press the Turbo key.
▶ Turbo heat: switch on heating mode and press the Turbo key.
Exiting the function:
▶ Press the Turbo key again.
3.6.6 Self-cleaning
The device has a self-cleaning function for the evaporator. The self-
cleaning freezes dust, mould and grease. Everything is then quickly
defrosted and dried with hot air.
▶ To activate the self-cleaning: press the Clean key.
CL appears on the display of the indoor unit when self-cleaning is in
progress. Self-cleaning ends automatically after 20 to 45 minutes.
Current time 13:00 o'clock
Setting of ON timer 4.0 h
Setting of OFF timer 8.5 h
Switch-on time 17:00 o'clock
Switch-off time 21:30 o'clock
To Next Page
Loading...
