Bosch FLEXIDOME multi 7000i

Other manuals for Bosch FLEXIDOME multi 7000i

Installation Manual44 pages

Questions and Answers

T
Thomas CooperJul 28, 2025
What to do if my Bosch IP Camera has no connection and no image transmission?
- D
  Dr. Erin YoungJul 28, 2025
  If your Bosch IP Camera isn't establishing a connection or transmitting images, there are several potential causes. First, verify all configuration parameters, and if needed, reset to factory defaults. Then, check all cables, plugs, contacts, and connections to ensure proper installation. Confirm that the IP address is correct by using the ping command. Also, check data transmission within the LAN using ping. Finally, if the maximum number of connections has been reached, wait until a connection becomes available before attempting to transmit again.
C
Christopher MoralesAug 4, 2025
Why my Bosch IP Camera does not operate?
- R
  Robert FordAug 4, 2025
  If your Bosch IP Camera unit does not operate, the possible cause is a power failure. Check the power supply to ensure it is functioning correctly. Also, verify whether PoE+ or a 24 V auxiliary input is being used. Another possible cause is faulty cable connections. Check all cables, plugs, contacts, and connections to ensure they are properly connected.
T
thomas86Aug 13, 2025
What to do if Bosch IP Camera is not operational after firmware upload?
- S
  smithpatriciaAug 13, 2025
  If your Bosch IP Camera is not operational after a firmware upload, it could be due to a power failure during the programming process. In this case, have the unit checked by Customer Service and replaced if necessary. Another possible cause is using an incorrect firmware file. To resolve this, enter the IP address of the unit followed by /main.htm in your web browser and repeat the upload, ensuring that you only use CPP14 firmware files.
G
guerrabrianAug 20, 2025
How to fix empty fields in web browser for Bosch IP Camera?
- R
  robert93Aug 20, 2025
  If your web browser shows empty fields while accessing your Bosch IP Camera, it's likely due to an active proxy server in your network. To fix this, create a rule in your local computer's proxy settings to exclude local IP addresses.

Summary

Browser Connection

System Requirements

Specifies the computer and network requirements for browser-based camera access.

Establishing Connection

Provides steps to connect to the camera using its IP address via a web browser.

Camera Password Protection

Details on setting up a mandatory service-level password for secure camera access.

System Overview

Live Page Overview

Description of the Live page for viewing live video streams and basic control.

Playback Page Overview

Description of the Playback page for accessing and viewing recorded video sequences.

Configuration Page Overview

Overview of the Configuration page for device and application interface settings.

Browser Operation

Live Page Functions

Detailed explanation of Live page features for video viewing and control.

Playback Page Usage

Instructions on navigating and using the Playback page to view recordings.

Search Recorded Video

Steps to search for specific recorded video content by date, time, and parameters.

Export Recorded Video

Instructions on how to export recorded video sequences from the device.

Dashboard Information

Details on the Dashboard page's information topics and data download options.

Configuration Settings

General Settings

General configuration for device identification, user management, and authentication.

Identification Settings

Configuration of device name, ID, video channel names, and host name.

User Management

Configuration of user accounts, authorization levels, and authentication modes.

Date and Time Configuration

Settings for date format, device time, time zone, and time server synchronization.

Web Interface Appearance

Customizing web interface appearance, language, and logos.

Live Functions Customization

Adapting Live page functions, video player, and audio transmission settings.

Connectivity Settings

Configuration for connecting to cloud services like Bosch Remote Portal and Stratocast.

Cloud Services Setup

Configuration details for Bosch Remote Portal and Stratocast cloud connectivity.

Account Configuration

Setting up FTP or Dropbox accounts for posting and recording export.

DynDNS Configuration

Setting up dynamic DNS service for Internet access via a host name.

Camera Settings

Configuration of camera installer menu, sensor modes, and image rotation.

Installer Menu Options

Configuration of sensor modes, image rotation, mirror image, and lens settings.

Display Stamping Configuration

Options for adding text overlays, logos, and time stamps to video images.

Positioning and Calibration

Settings for camera positioning, calibration, and perspective for video analytics.

Scene Mode Settings

Configuration of various scene modes for optimizing image capture.

Color Adjustment

Settings for adjusting brightness, contrast, saturation, and white balance.

ALC Control

Configuration of Automatic Level Control modes and levels for video output.

Image Enhancement

Settings for enhancing image quality like backlight compensation and noise reduction.

Encoder Streams Setup

Configuration of video encoder streams, limits, prioritization, and profiles.

Privacy Masks Configuration

Defining privacy masks to block specific areas from the camera's view.

Audio Settings

Configuration of audio input, volume, recording format, and audio transmission.

Pixel Counter Function

Using the Pixel Counter to measure horizontal and vertical pixels in the image.

Recording Management

Options for recording images to iSCSI systems or SD cards.

Storage Management

Managing storage media, including iSCSI and local media setup.

Recording Profiles Setup

Defining and configuring recording profiles for different tracks and scenarios.

Maximum Retention Time

Setting the maximum retention time for recordings before overwriting.

Recording Scheduler

Scheduling recording profiles based on weekdays, holidays, and time periods.

Image Posting Setup

Configuring the saving of JPEG images to an FTP server at specific intervals.

SD Card Status

Details about the installed SD card, including manufacturer, size, and lifespan.

Alarm Configuration

Alarm Connections

Setting up automatic connections and actions upon alarm events.

Video Content Analysis (VCA)

Configuring integrated VCA features for detecting and analyzing image changes.

Audio Alarm Setup

Setting up alarms based on audio signals, configuring signal strength and frequency.

Alarm Email Notifications

Configuring email notifications for alarms with optional JPEG attachments.

Alarm Input Configuration

Configuring alarm triggers for external contacts and defining actions upon input.

Alarm Output Control

Configuring output behavior based on selected events and defining modes.

Alarm Task Editor

Editing alarm functions using script form, overwriting other alarm settings.

Network Configuration

Network Services

Activating or deactivating available network services for the device.

Network Access Settings

Configuring IP address, subnet mask, gateway, and automatic IPv4 assignment.

Advanced Network Options

Advanced network settings including RTSP, 802.1x authentication, and metadata input.

Network Management (SNMP)

SNMP configuration for managing network components and sending traps.

Multicast Streaming

Enabling multicast streaming for multiple receivers and configuring addresses.

CloudWatch Integration

Enabling Amazon CloudWatch for monitoring and management services.

Service and Maintenance

Maintenance Operations

Performing maintenance tasks like firmware updates and configuration backup/restore.

License Management

Activating additional functions using activation keys and viewing installed licenses.

Certificate Management

Managing certificates for secure communication and authentication.

Logging Configuration

Configuring event logging levels, software sealing, and downloading logs.

System Overview Information

Viewing system information for technical support purposes.

Troubleshooting Guide

Physical Reset Button Usage

Instructions on using the physical reset button to restore factory defaults.

Appendices and Support

Copyright Notices

Legal notices and copyright information for firmware and software.

Support and Resources

Links to support services, training courses, and documentation.

Bosch FLEXIDOME multi 7000i Specifications

General

Camera Type	Dome
Sensor Type	CMOS
Day/Night Functionality	Yes
Video Compression	H.265, H.264, MJPEG
Ingress Protection	IP66
Impact Protection	IK10
Sensors	1/1.8-inch CMOS
Focal Length	2.8 - 10 mm
Minimum Illumination	B/W: 0.01 lux (typical values, varies by model)
Infrared	No
WDR	Yes (120 dB)
Frame Rate	Up to 30 fps
Audio	Two-way audio
Analytics	Intelligent Video Analytics
Power	PoE (Power over Ethernet) or 24 VAC