Why is my Bosch LV036 Heat Pump compressor not running but the fan is, possibly due to low airflow?
If your Bosch Heat Pump's compressor isn't running but the fan is, it could be due to a low-pressure fault caused by no or low airflow. Check the fan motor to ensure it is operating correctly.
What to do if my Bosch LV036 compressor isn't running but the fan is, and I suspect airflow issues?
If your Bosch Heat Pump's compressor isn't running but the fan is, it could be due to a high-pressure fault caused by no or low airflow. Check the fan motor to ensure it is operating correctly.
How to troubleshoot a Bosch Heat Pump with no compressor operation but running fan, possibly due to a fouled water coil?
If your Bosch Heat Pump's compressor isn't running but the fan is, it could be due to a high-pressure fault caused by a fouled or scaled water coil. Check for proper flow rate and water temperature, especially looking for a low water side temperature rise during cooling.
Why is my Bosch LV036 compressor not running but the fan is, possibly due to high water temperature?
If your Bosch Heat Pump's compressor isn't running but the fan is, it could be due to a high-pressure fault caused by high water temperature. Check the water temperature to ensure it is within the appropriate range.
What to do if the compressor of my Bosch Heat Pump doesn't work but the fan runs and there is a freeze fault?
If your Bosch Heat Pump's compressor isn't running but the fan is, it could be due to a freeze fault in the water coil caused by no or low water flow. Check the water valves and/or pumps to ensure they are operating correctly. Also, check the water coil for any blockages.
What to do if my Bosch LV036 Heat Pump compressor isn't running and the fan is on, but I suspect low refrigerant?
If your Bosch Heat Pump's compressor isn't running but the fan is, it could be due to a low-pressure fault caused by low refrigerant. Check the refrigerant pressure with a gauge set.
How to reduce objectionable noise levels from my Bosch LV036 Heat Pump?
If you're experiencing objectionable noise levels from your Bosch Heat Pump, ensure the duct work and grilles are properly sized for unit air flow. If the fan speed setting is too high, consult the blower performance table and reduce fan speed if possible. To address structure borne noise, mount the unit on a vibration pad. Also, install the unit in accordance with the provided instructions and adjust the unit location to prevent it from touching the structure.
Warns about hazards from improper installation, adjustment, alteration, service, or use.
States that installation/servicing is hazardous and requires trained personnel.
Emphasizes servicing by qualified technicians to prevent refrigerant release.
Mandates proper recovery of discharged refrigerant per industry and legal standards.
Advises against using units for construction heating/cooling to prevent damage/warranty void.
Instructions for preparing the job site before unit installation.
Procedures for inspecting the unit upon shipment for damage or discrepancies.
Guidance on selecting the proper location for unit installation, considering access and environment.
Critical safety warning about securely anchoring hanging rods to the ceiling.
Guidelines for wiring high voltage power supply to the unit.
Critical safety warning about the use of the ground wire.
Safety warning regarding routing control and power wiring.
Details on connecting and configuring the ECM-UPM control system.
Explains how safety devices integrate with the UPM control board.
A checklist of system checks to perform before initial startup.
Safety warning about high voltage presence in the electrical panel.
Instructions for verifying correct compressor rotation direction.
Critical safety warning before performing system flushing.
Emphasizes the need for specialized knowledge for closed loop/pond applications.
Critical notice about water quality's impact on unit life and warranty.
Critical safety warning regarding screw reuse during motor speed adjustment.
Safety warning to follow codes for unit hanging.
Describes ECM motors and how to change speed taps.
Provides a guide to diagnosing and resolving common unit problems.
Addresses scenarios where the fan runs but the compressor does not engage.
Covers troubleshooting steps for high pressure faults due to water or air flow issues.
Covers troubleshooting steps for low pressure faults related to refrigerant or water flow.
Covers troubleshooting steps for freeze faults related to water temperature or refrigerant.
Diagnosing issues related to condensate drainage and power supply problems.
Addressing freeze faults, airflow restrictions, and refrigerant levels.
Troubleshooting thermostat calls, connections, and contactor problems.
Diagnosing compressor overload, wiring, and burnout issues.
Troubleshooting lack of unit operation due to power or transformer issues.
Diagnosing fan motor issues for both PSC and ECM types.
Diagnosing fan operation for airflow motors and unit mode shifting issues.
Troubleshooting causes for incorrect supply air temperatures in cooling and heating.
To Next Page
General
