Need help?Do you have a question about the Bosch NIN-733 and is the answer not in the manual?
General| Type | IP security camera |
|---|---|
| PTZ control | - |
| Day/night mode | Yes |
| Placement supported | Indoor & outdoor |
| Connectivity technology | Wired |
| Form factor | Dome |
| Product color | White |
| Housing material | Aluminum |
| Protection features | Vandal proof |
| International Protection (IP) code | IP66 |
| Total megapixels | 1.4 MP |
| Maximum resolution | 1280 x 720 pixels |
| Supported video modes | 720p |
| Video formats supported | H.264, M-JPEG |
| Analog signal format system | NTSC, PAL |
| Supported graphics resolutions | 432 x 240, 704 x 480, 768 x 432, 1280 x 720 (HD 720), 854 x 480 (WVGA) |
| Pan range | 0 - 360 ° |
| Tilt angle range | 0 - 90 ° |
| Angle of rotation | 90 ° |
| Camera shutter type | Electronic |
| Camera shutter speed | 1/60- 1/15000 s |
| Minimum illumination | 0.01 lx |
| Sensor type | CMOS |
| Optical sensor size | 1/3 \ |
| Optical zoom | - x |
| Focal length range | 10 - 23 mm |
| Compatible memory cards | MicroSDHC, MicroSDXC |
| Cabling technology | 10/100Base-T(X) |
| Supported network protocols | IPv4, IPv6, UDP, TCP, HTTP, HTTPS, RTP/RTCP, IGMP V2/V3, ICMP, ICMPv6, RTSP, FTP, Telnet, ARP, DHCP, NTP (SNTP), SNMP (V1, MIB-II), 802.1x, DNS, DNSv6, DDNS (DynDNS.org, selfHOST.de, no-ip.com), SMTP, iSCSI, UPnP (SSDP), DiffServ (QoS), LLDP, SOAP, Dropbox, CHAP, digest authentication |
| Ethernet LAN (RJ-45) ports | 1 |
| Audio formats supported | LC-AAC |
| Signal-to-Noise Ratio (SNR) | 50 dB |
| AC input voltage | 24 V |
| Power source type | PoE |
| AC input frequency | 50 - 60 Hz |
| Power consumption (typical) | 7.2 W |
| Storage temperature (T-T) | -50 - 70 °C |
| Operating temperature (T-T) | -30 - 50 °C |
| Operating relative humidity (H-H) | 5 - 93 % |
Weight and Dimensions| Depth | 158 mm |
|---|---|
| Height | 124 mm |
| Weight | 1280 g |
High risk: This symbol indicates an imminently hazardous situation such as 'Dangerous Voltage' inside the product.
Read, follow, and retain for future reference all of the following safety instructions.
The yellow/green safety (power) ground wire from the camera must be connected to the system earth.
The camera incorporates a network video server. Its primary function is to encode video and control data for transmission over an IP network.
The camera can be configured using a browser on the local network (Intranet) or from the Internet.
The camera/housing unit consists of the following parts: Surface Mount Box, Camera module and mounting base, Inner liner, Dome cover.
Use the surface mount box as a template to mark the holes indicated in the drawing. The PCD is 123 mm (4.84 in).
Use the mounting template to mark out the recess and to mark the holes indicated in the drawing. The PCD is 133 mm (5.25 in).
Information on making electrical and network connections for the camera unit.
Use a class 2 power supply 24 VAC or +12 VDC. Connect the power wires (red+, brown-) to the power supply.
Use a shielded twisted pair (STP) Category 5e cable, maximum length 100 meters.
The camera module position can be adjusted along three axes and several zoom positions can be selected.
For horizontal adjustment (pan): Rotate the camera module (1) in the base. Do not rotate more than 180° in either direction.
For vertical adjustment (tilt): Loosen the two thumbwheels (1). Swing the camera module between the wings.
The following table is intended to help identify the causes of malfunctions and correct them where possible.
If a fault cannot be resolved, please contact your supplier or system integrator, or go directly to Bosch Security Systems Customer Service.
Details the technical specifications of the camera, including imager, resolution, voltage, and consumption.
To Next Page