Bosch WBN 6000-24 CR

To Next Page

To Previous Page

Installation

Gaz 6000 W – 6720866247 (2019/07)

Checking the gas line for tightness

▶ Close the gas isolator to protect the gas valve against damage from

excess pressure.

▶ Check all joints for tightness (test pressure: max. 150 mbar).

▶ Depressurise the system.

Main Page

Table of Contents2
Explanation of Symbols and Safety Instructions4
Explanation of Symbols4
General Safety Instructions4
Product Information6
Scope of Delivery6
Declaration of Conformity6
Product Identification6
Overview of Types6
Dimensions and Minimum Clearances7
Product Overview9
Regulations for Gas Systems10
Flue Gas Routing11
Approved Flue Accessories11
Installation Instructions11
Selecting the Fan Stage12
B22 Horizontal Flue Gas Routing12
B22 Vertical Flue Gas Routing12
C12, C42 Horizontal Flue Gas Routing with Concentric Pipe13
C12, C42, C82 Horizontal Flue Gas Routing with Separate Pipe13
C32 Vertical Flue Gas Routing with Concentric Pipe14
C32, C52 Vertical Flue Gas Routing with Separate14
Pipe14
Installation16
Prerequisites16
Solar Preheated Water (Only WBN 600016
Fill and Top-Up Water16
Checking the Size of the Expansion Vessel17
Installing the Device17
Filling the System and Checking for Tightness18
Electrical Connection20
General Notes20
Connect the Device20
Control Device Terminals21
Connecting the On/Off Controller or Opentherm Controller21
Replacing the Power Cable21
Connecting a Cylinder Temperature Sensor (WBN 600021
Connecting an Alarm Contact21
Commissioning22
Control Panel Overview22
Display Readings22
Switching on the Appliance22
Setting the Flow Temperature22
Setting the DHW Heating23
Adjust the Domestic Hot Water Temperature23
Setting the Heating Controls23
After Commissioning23
Setting Summer Mode23
Shutdown24
Switching Off/Standby Mode24
Setting Frost Protection24
Anti-Block Protection24
Thermal Disinfection (WBN 600025
Heating Pump25
Changing the Heating Pump Curve25
Settings in the Service Menu26
Operating the Service Menu26
Service Functions Overview27
Menu 127
Menu 228
Menu 329
Restoring Values to Default Setting29
Check Gas Setting30
Gas Type Conversion30
Gas Setting (Natural Gas and LPG)30
Preparation30
Burner Pressure Adjustment31
Flue Gas Test32
Setting Appliance Output32
Tightness Test of the Flue Gas Path32
Checking the CO Level in the Flue Gas32
Testing Flue Gas Loss Value32
Environmental Protection and Disposal33
Inspection and Maintenance34
Safety Instructions for Inspection and Maintenance34
Description of Various Workflow Steps35
Calling up the Last Fault Saved35
Opening the Appliance35
Checking the Strainer in the Cold Water Pipe (WBN 600035
Clean Burner Body, Nozzle and Burner36
Cleaning the Heat Exchanger36
Checking the Expansion Vessel36
Setting the Heating System Operating Pressure36
Checking Electrical Wiring37
Removing the DHW Temperature Sensor37
Unblocking the Pump (E.g. When Commissioning the System)37
Checklist for Inspection and Maintenance38
Readings on the Display39
Faults39
Troubleshooting39
Faults that Are Shown on the Display40
Faults that Are Not Shown on the Display41
Appendix42
Commissioning Report for the Device42
Electrical Wiring44
Technical Data45
Sensor Values47
Flow Temperature Sensor47
DHW Temperature Sensor47
Setting Values for Central Heating/Dhw Output48

Bosch WBN 6000-24 CR - Page 19

Table of Contents

Other manuals for Bosch WBN 6000-24 CR

Related product manuals