Need help?Do you have a question about the Broadcast DPS ES-2200 and is the answer not in the manual?
General| Brand | Broadcast |
|---|---|
| Model | DPS ES-2200 |
| Category | Computer Accessories |
| Language | English |
Provides a general overview of the DPS ES-2200 expansion system and its two versions, ES-2200T and ES-2200S.
Describes the DPS Personal TBC card, its function as a full frame TBC for interfacing video sources.
Explains the DPS MicroSYNC as a four-field composite video synchronizer for locking signals to a video system.
Details the DPS Personal V-Scope, a waveform monitor and vectorscope for real-time video signal monitoring.
Describes the DPS Personal Video Routing Switcher, a composite video switcher with 4x1 and 8x1 matrices.
Introduces the DPS Personal VDA, a video distribution amplifier for driving multiple loads from one input.
Details the items included with the ES-2200 Expansion System and suggests retaining packing materials.
Provides guidelines for mounting the ES-2200 in racks or consoles, emphasizing ventilation and clearance.
Explains how to set cards and configure them for operation from the ES-2200 front panel, including handling static electricity.
Outlines the possible card configurations for the ES-2200T chassis, including single and dual card installations.
Provides step-by-step instructions for installing cards into the ES-2200T chassis, including DIP switch settings and cable connections.
Lists the possible card combinations for the ES-2200S chassis, accommodating MicroSYNC and other DPS cards.
Details the procedure for installing cards into the ES-2200S chassis, covering DIP switches, connections, and baud rate settings.
Explains how to select units and activate remote mode on the ES-2200T for front panel and external control.
Details Proc Amp, Memory, Balance, and Freeze controls for TBC cards on the ES-2200T.
Covers SYSTEM TIMING, GENLOCK controls, and INPUT SELECT for TBC cards.
Outlines the steps to configure TBC cards with various setup modes using front panel buttons and the shaft encoder.
Lists and describes TBC configuration functions and specific controls for TBC IV option cards.
Explains V-Scope controls for display modes, superimpose, freeze, and frequency response.
Describes how the ES-2200T controls the RS-2800 routing switcher, focusing on the 4x1 matrix.
Details how to control an 8-bit MicroSYNC card when installed in the ES-2200T chassis.
Explains how to select units and activate remote mode on the ES-2200S for front panel and external control.
Details Proc Amp and Freeze controls as they apply to MicroSYNC cards.
Covers Memory functions and PROCESS/BYPASS modes for MicroSYNC cards.
Explains Timing, H-POS, C-F Genlock, and Clip adjustments for MicroSYNC cards.
Outlines the steps to select and change configuration functions for the MicroSYNC card using setup options.
Lists and describes various configuration functions for the MicroSYNC card.
Explains V-Scope controls for display modes, superimpose, freeze, and frequency response.
Describes how the ES-2200S controls the RS-2800 routing switcher, focusing on the 4x1 matrix.
Details I/O connectors for TBC III and TBC IV cards, covering various video and genlock inputs/outputs.
Lists I/O connectors for 8-Bit MicroSYNC and MicroSYNC-X cards, including genlock, remote, and video signals.
Details I/O connectors for the Personal V-Scope card, including remote input and video outputs.
Describes connectors for the Routing Switcher, including remote input, 4x1 inputs, and BNC output.
Lists connectors for the VDA card, including termination switch, gain pots, video input, and outputs.
Describes DPS software for controlling ES-2200 units and installed cards via PC or Amiga.
Explains establishing unique card addresses using DIP switches for software control of the ES-2200 system.
Details using the RC-2000 remote for controlling DPS cards and ES-2200 units, requiring matching baud rates.
Describes RC-2001 remote control and assigning unique hexadecimal addresses to DPS products for control.
Details ES-2200 specifications including serial input, power, and physical characteristics.
Describes the serial interface and communication protocol for controlling the ES-2200, including MIDI compatibility.
Explains function bytes and data for controlling TBC cards via commands.
Lists configuration bytes for setting MicroSYNC card parameters.
Details configuration bytes for setting TBC IV card parameters.
Explains function select and data bytes for controlling V-SCOPE card functions.
Provides contact addresses and phone numbers for Digital Processing Systems support.
Outlines the warranty period, conditions, and limitations for the DPS product.
Provides instructions for obtaining warranty repair service, including RMA requirements.
States the device's compliance with FCC Part 15 rules and operational conditions.
To Next Page