To Next PageTo Next PageWhat to do if CaptiveAire Industrial Equipment is out of schedule?
If the RTULink has lost its connection to CASLink and has run out of schedule tasks, verify that the RTULink is reporting via the CASLink profile. Once communication with CASLink has been verified, setup and push a valid schedule.
How to troubleshoot Heating Discharge Temp issue in CaptiveAire RTULink Industrial Equipment?
If the heating stage has failed, meaning the temperature rise between return and discharge is not adequate, check the heating stage operation and ensure that each stage achieves a proper temperature drop from the inlet temperature.
What to do if Space Temp is Not Connected in CaptiveAire RTULink Industrial Equipment?
If the temperature sensor has been disconnected or has failed, verify correct resistance across Type II 10k? thermistor and replace if the sensor is faulty.
What to do if Outside Temp is Not Connected in CaptiveAire RTULink Industrial Equipment?
If the temperature sensor has been disconnected or has failed, verify correct resistance across Type II 10k? thermistor and replace if the sensor is faulty.
What to do if Return Temp is Not Connected in CaptiveAire RTULink?
If the temperature sensor has been disconnected or has failed, verify correct resistance across Type II 10k? thermistor and replace if the sensor is faulty.
What to do if Discharge Temp is Not Connected in CaptiveAire RTULink Industrial Equipment?
If the temperature sensor has been disconnected or has failed, verify correct resistance across Type II 10k? thermistor and replace if the sensor is faulty.
What to do if Mixed Air Temp is Not Connected in CaptiveAire Industrial Equipment?
If the temperature sensor has been disconnected or has failed, verify correct resistance across Type II 10k? thermistor and replace if the sensor is faulty.
Why is Outside RH Not Configured in CaptiveAire Industrial Equipment?
If the enthalpy economizer is configured on the RTULink but an outside air relative humidity sensor is not configured, verify that an outside air relative humidity sensor is connected to one of the RTULink inputs. Install and connect one if one has not already been connected. Once the sensor is connected, configure the sensor via the onboard HMI.
What causes Return RH Not Configured error in CaptiveAire Industrial Equipment?
If differential enthalpy economizer is configured on the RTULink but a return air relative humidity sensor is not configured/connected, verify that a return air relative humidity sensor is connected to one of the RTULink inputs. Install and connect one if one has not already been connected. Once the sensor is connected, configure the sensor via the onboard HMI.
Describes the RTULink system and general safety.
Provides safety precautions for installation procedures.
Instructions for installing the main RTULink board.
Details on installing thermistor sensors.
Installation of the outdoor air temperature sensor.
Installation of the return air temperature sensor.
Installation of the discharge air temperature sensor.
Wiring the RTULink board to the RTU.
Wiring an external thermostat to the RTULink.
Installing a wall-mounted space temperature sensor.
Connecting RTULinks for Modbus communication.
Installing wall-mount temp/humidity sensors.
Installing outdoor temp/humidity sensors.
Installing duct-mounted RH sensors.
Installing duct-mounted CO2 sensors.
Installing current transducers for energy monitoring.
Controlling dampers/economizers with 0-10VDC output.
Controlling powered exhaust with 24VAC signal.
Controlling powered exhaust with 0-10VDC signal.
Using a 24VAC signal for occupancy control.
Mode for maximum remote control and customization.
Mode for monitoring without control.
Hybrid mode with thermostat control and RTULink logic.
Operation mode for emergency heating function.
Viewing operating information and status.
Accessing and modifying system settings and parameters.
Information on active and historical faults.
Procedure for restarting the RTULink system.
How to navigate and access HMI settings.
Connecting and using remote HMIs.
Overview of user, factory, and service menus.
Description of user settings and options available on the HMI.
Parameters for heating operation and staging.
Parameters for cooling operation and staging.
Settings related to the control board itself.
Configuration for blower operation and delays.
Configuration for economizer and CO2 based ventilation.
Settings related to service, monitoring, and factory reset.
Lists common RTULink fault messages and corrective actions.
Description of wall-mount temperature sensors.
Description of current transducers for energy measurement.
Description of outdoor temp/humidity sensors.
Description of duct-mounted CO2 sensors.
Diagrams for daisy chain communication wiring.
Diagrams for star communication wiring.
Explanation of fixed dry bulb economizer operation.
Explanation of differential dry bulb economizer operation.
Explanation of fixed enthalpy economizer operation.
Explanation of differential enthalpy economizer operation.
General| Manufacturer | CaptiveAire |
|---|---|
| Enclosure Rating | NEMA 4X |
| Power Supply | 24 VAC/DC |
| Communication Protocol | Modbus RTU |
| Operating Temperature | -40°C to 70°C |
| Type | Remote Terminal Unit (RTU) |
