What to do if the Cardinal 225 indicator is attempting to display a number greater than seven digits?
If the Cardinal Scales indicator attempts to display a number exceeding the digit limit, this may indicate miscalibration. Return to Gross Weight mode and review the Tare value.
What to do if motion is present when trying to power up, print, zero or perform a push button tare function on Cardinal 225 Scales?
If there is motion present while attempting to power up, print, zero, or perform a push-button tare function on Cardinal Scales, wait for a stable weight display (STABLE symbol on) before performing any of these operations.
What to do if EEPROM checksum failure occurs on Cardinal 225 Scales?
If an EEPROM checksum failure occurs, indicating improper stored calibration data, recalibrate the Cardinal Scales with a calibrated test weight.
What to do if Cardinal Accessories scale shows OVERCAP?
If your Cardinal Accessories scale displays 'OVERCAP', it means the load on the scale exceeds its capacity, possibly due to miscalibration. Remove the excess weight from the scale. If the problem persists, it's advisable to consult a scale service provider for recalibration.
What to do if the load cell input is below the allowed range of the Cardinal 225 Scales indicator?
If the load cell input is below the allowed range, this may indicate a load cell or circuit failure. Check for improper load cell wiring and ensure the output is between 1 to 40mV.
What to do if the load cell input is above the allowed range of the Cardinal 225 Scales indicator?
If the load cell input exceeds the indicator's allowed range, it may be caused by load cell or circuit failure. Check for improper load cell wiring, excessive load, and verify the output is between 1 to 40mV.
Why is Cardinal Scales displaying incorrect weight?
Several factors can cause Cardinal Scales to display an incorrect weight: * Verify the indicator has been calibrated. * Ensure the scale platform isn't touching any adjacent objects. * Check the load cell connector wiring. * If using four-wire load cells, ensure the sense lead jumper (J9) is installed. * Confirm proper operating procedures are being followed.
What to do if Cardinal Scales display does not turn on?
If the Cardinal Scales display doesn't turn on: * Ensure the AC power cord is fully inserted into the wall receptacle. * Check the wall receptacle for proper AC power by testing with another electrical appliance. * Check the circuit breaker. * Consider if there has been a power failure.
Why is the Cardinal 225 load exceeding capacity?
The Cardinal Scales may display this issue due to miscalibration. Remove the excess load from the scale platform. Consult your scale service provider regarding recalibration.
How to fix CAL LOST CONFIG REQUIRED on Cardinal Accessories?
The 'CAL LOST CONFIG REQUIRED SCALE X' error on your Cardinal Accessories indicates an EEPROM checksum failure, meaning the stored calibration data is improper. You will need to recalibrate the scale using a calibrated test weight.
Explains logic level outputs for controlling peripheral devices based on weight limits.
Step-by-step instructions for routing and connecting output cables to the indicator.
Details AC output relay boards (RB4-ACOUT, RB8-ACOUT) for external junction boxes.
Procedure for installing cables for remote inputs to the indicator's terminal block P17.
Describes AC input relay boards for 115 VAC and 230 VAC versions, supporting multiple inputs.
Identifies key connectors on the main PC board, such as P15, P16, P17, and P18.
Configures active remote output jumpers for sourcing 5 VDC or isolated outputs.
Configures the remote input jumper for sourcing 5 VDC or isolated inputs.
Jumpers for enabling automatic power-on and activating the backlight test.
Details jumpers for excitation, sense leads, dead load boost, and ground connection.
Procedure to navigate to the Check Weigher setup menus.
Setting the number of check weigher outputs (3-zone or 5-zone comparison).
Configuring the automatic print feature based on weight stability and range.
Explains relay outputs for 3-zone (OUTPUTS=3) and 5-zone (OUTPUTS=5) comparisons.
Procedure to enter UNDER and OVER preset values for 3-zone operation.
Procedure to enter UNDER, LOW OK, HIGH OK, and OVER presets for 5-zone operation.
General| Auto Shut-off | Yes |
|---|---|
| Tare Function | Yes |
| Capacity | 225 lbs |
| Graduation | 0.1 lb |
| Power Source | Battery (included) |
To Next Page
