Carrier 42C Series - Page 24

24
Fig. 19 — 42CG Horizontal Cabinet
Optional Stamped
Return Air Grille
and 1" [25] Filter
4-7/8
[125]
Max.
3-1/2
[89]
9-1/4
[236]
18-3/8
[466]
See Notes
e,g,h
2
[51]
2
[51]
E
A
2
[51]
9-3/8
[237]
Unit Label and
Wiring Diagram
(See Note f)
Optional "L" Shaped
Drip Lip. Shipped Loose
(See Note d)
Chilled/Hot Water
Supply and Return
Connections
(See supplemental drawing
for coil stubout locations.)
10.220
[259.59]
(Size 06-12)
9
[229]
(Size 02-04)
1-3/4
[43]
3-3/4
[94]
1-1/2 [38]
Knockout
(Typ. of 8)
7/8 [22] Knockout
(Typ. of 2)
Partial Rear View
(Typical Both Sides)
See valve pkg supplement
for dimensions.
Right Side View
23-7/8
[606]
2-1/2
[62]
5-3/4
[146]
1-1/2
[38]
F
G
Supply
Air
2
[51]
Return
Air
7/8 [22] O.D.
Condensate Drain
Connection
Standard Stamped
Return Air Grille
and 1" [25] Filter
Optional Return Air
Location Follows Dim. B
for Width Flange 1 [24]
Removed Hinged
R.A/Access
Panel
Detail A
Stub Out locations
for standard coils
4-1/4
[108]
2-1/8
[53]
1
[25]
2-3/4
[71]
4-1/8
[106]
5-1/2
[141]
Front View
Standard Stamped
Supply Air Grille
Resilient Mounting
Grommet with
3/8 [10] Dia. Holes
(Typ. of 4)
C
B
C
Top View
Optional
Service
Switch
LEGEND
CR — Cold Water Return
HR — Hot Water Return
CS — Cold Water Supply
HS — Hot Water Supply
UNIT
SIZE
42CG
DIMENSIONS in. [mm]
a,b,c,d,e,f,g,h,i,j,k
NOTE(S):
a. Right-hand units shown, left-hand opposite.
b. All dimensions are ± .25 [6]. Drawing not to scale.
c. Product specifications are subject to change without notice.
d. Drip lip recommended. Provided when valve package is ordered.
e. Control box size and position may vary. Consult factory.
f. Position may vary.
g. Service entrance is located on the rear of the control box with knockouts.
h. Units without service switch use the knockouts on the rear side of the control box.
i. Typical size 06 unit shown with 1-Motor and 2-Blower. Refer to table for variation.
j. See valve package supplemental for piping termination.
k. Field connection pipes will be shipped loose with valve packages.
QTY/UNIT
AB C E F GBlowerMotor
02 38 [965] 17-1/8 [435] 10-7/16 [265] 34 [864] 5-3/4 [146] 11 [279] 1 1
03 42 [1067] 21-1/2 [546] 10-1/4 [260] 38 [965] 5-3/4 [146] 11 [279] 1 1
04 48 [1219] 25-7/8 [657] 11-1/16 [281] 44 [1118] 5-3/4 [146] 11 [279] 2 1
06 53 [1346] 34-5/8 [879] 9-3/16 [233] 49 [1245] 6-3/4 [171] 12 [305] 2 1
08 60 [1524] 39 [991] 10-1/2 [267] 56 [1422] 6-3/4 [171] 12 [305] 2 1
10 74 [1880] 52-1/8 [1324] 10-15/16 [262] 70 [1778] 6-3/4 [171] 12 [305] 4 2
12 82 [2083] 60-7/8 [1546] 10-9/16 [268] 78 [1981] 6-3/4 [171] 12 [305] 4 2