Carrier 59SC2A - Page 6

Og
-0¢4
O¢-004 pe-OOL 0¢g-080 gt-080 vi-090 O%-090 Ob-O0v0
dZIS
JDVNYNA
ZOS6S
(zz9)
@/t-ve
(e69)
12
(Spb)
Z/k-Lb
(498)
9t/e-pL
HLGIM
LANIgVo
1d
-
1°31
(.99)
9/2
-2z
(260)
9/E-64
(e0r)
e/2-St
(6i8)
Z/t-zZt
HLGIM
L371LNO
ISUSUL
Big
jeuo
SuIA
(pes)
6
(900)
OF
(zz)
91/6-zZ4
(6%)
Z/L-64
HLGIM
LAINI
WOLLOG
(zzz)
v/e-8
(484)
O/k-Z
SYVLNI
IV
(Lis)
p/k-Zt
(292)
Z/k-Ob
(268) O'984 (9°92)
S891
(9°92)
S891
(2°22)
FbOL
(€°69)
O'PSt
(8°79)
O'rrt
(Z'29)
O'224
(p'9S)
O'eek
(oy)
a1
‘LM
dIHS
LOE21LV
—~ 6 15/16
[176.1]
23/10
{524i
NOTES:
1. Doors may vary by model.
59SC2A
2. Minimum return-air openings at furnace, based on metal duct. If flex duct is used,
see flex duct manufacturer's recommendations for equivalent diameters.
a. For 800 CFM-16-in. (406 mm) round or 14 1/2 x 12-in. (368 x 305 mm) rectangle.
b. For 1200 CFM-20-in. (508 mm) round or 14 1/2 x 19 1/2-in. (368 x 495 mm) rectangle.
c. For 1600 CFM-22-in. (559 mm) round or 14 1/2 x 22 1/16-in. (368 x 560mm) rectangle.
i d. Return air above 1800 CFM at 0.5 in. w.c. ESP on 24.5" casing, requires one of the following
3, configurations: 2 sides, 1 side and a bottom or bottom only. See Air Delivery table in this
AIR INTAKE document for specific use to allow for sufficient airflow to the furnace.
ropuew wl ene be 3. Vent and Combustion air pipes through blower compartment must 2912
(170.1 use accessory “Vent Kit - Through the Cabinet”. See accessory list for (7493)
current part number. 2634 ________-|
oan 16 (730,5]
: 26.11/16 ———_»|
26 3/8 [678.1]
[670.0]
ava
26
3/8
|
[638.7]
[669.9]
#23 5/16
[592.9]
ier
—
|g ee —— & ———_ 211/16 =»
2058
[535.8]
8 205/8 ————__»
asa} OUTLET WIDTH 522.7]
O ts
[76.2]
AIR INTAKE
AIR FLOW 13/4 [15.8] AIR FLOW AIRFLOW
fas Ht ven oN
[22.2]
y
e134
CONDENSATE DRAIN TRAP. 3 . GAS CONN
LOCATION
4
VENT
|
|
Drie
[101.6]
[22.2]
z D3
[762] B78
| (22.2)
Bre rt 212 JAD
[22.2] 22 35 [63.5] 4
O78 = as 28 3/16 \@ _-@| Bere jisto
[22.2] POWER CONN 32 78
(222) Ng 1715.9] (8295) > i 22.2] POWER CONN
r — t 28 5/8 ® ® ene 28/8 —_ q
SIDE INLET 237/16 1726] M50 | ipo) gh 7/@ SDE INLET
20 1/4
B78 (595.6) 25 3/16 285/8 (22.2]
(oy rears ] 1639.1] (72691 | ggg i776 Ko dm
THERMOSTAT ENTRY 22 15/16 . [22.2]
14 13/16 17 5/16 [5819] e 20/4 169/16 THERMOSTAT ENTRY
[376.3] [439.2] 1513.9] 18/16 | iay69)
[458.6] .
t _— oe J
|
p— 1 {BOTH SIDES} 1iie | c 1116 BOTTOM INLET
[25.4]
SEE
NOTE
#3
BOTTOM
RETURN
(175)
pean
jue
22 WIDTH ’ 2
[558.3] (BOTH SIDES} p< 23 3/8 ———_______»»
21
NOTE:
ALL
DIMENSIONS
IN
INCH
[MM]
15/16
[592.0]
(534.0) [33.3] 26 5/16
bx 265/16 {668.2}
[668.3]
=
Siena *)*
‘EE