Cedima CF-2116 D - Information Concerning Machine Operation; Special- and Maintenance Work

ENGLISH
13
General safety instructions
• CEDIMA
®
• Technical Documentation • All rights reserved as per ISO 16016 • Subject to modications due to progressive development •
• Make sure that the machine is only used when in a
safe, operative condition! Only operate the machine
when all safety equipment and safety-related
equipment (e.g. guards, emergency-stop devices,
noise insulation etc.) are present and operative!
• Check the machine for externally recognisable
damage and defects before each use. Immediately
report any changes (including changes in operating
behaviour) to the responsible ofce/person!
• In the event of malfunctions or if the machine
behaves differently, shut it down immediately and
prevent it from being restarted. Have faults rectied
immediately!
• Check the following before the start of cut:
- the kind of material to be cut (in this case wet cut)
- the kind of work, and that the diamond saw blades
recommended by the manufacturer are compatible!
- the proper condition of the diamond saw blade (no
deformation, damages)
- the diameter of the saw blade recommended by the
manufacturer
- the cutting speed (RPM.) of the diamond saw blade
(max. RPM) of the machine recommended by the
manufacturer
- the accordance of the machine`s direction of cut to
the direction of cut of the diamond saw blade
- the compatibility of the diamond saw blade to the
arbour (ange)
- the rm seating of the diamond saw blade.
Secure the t of the diamond saw blade
(mounting according to recommendations of the
manufacturer, with only original screws!
• The direction of rotation of machines with electrical
AC motors or hydraulic drive must be maintained to
prevent loosening of the saw blade!
3.6 Information concerning machine
operation
• Observe the procedures for switch-on and switch-
off, as well as the indicating devices described in the
operating manual!
• Before switching on the machine or putting it into
gear, make sure that it cannot pose a danger to
anyone during start-up or operation.
• Only qualied operators are to be in the range of
the machine. Other persons are to be kept at a safe
distance!
• The machine may only be started from the operators/
drivers place at the back (CF-2116) of the machine!
• Take precautions to ensure that the operator always
has an adequate view of the working area and can
intervene in the work process at any time!
• Before starting work, make sure that all brakes,
steering, signals and lighting are in working order!
• Hydraulic and water hoses as well as electrical
cables must be installed so that damage by tools or
the machine are not possible!
• Cutting must be carried out with water to prevent
the forming of health-endangering ne dusts, and to
increase the service life of the cutting tool!
• When wet-cutting, make sure that enough water is
available where it is needed. Cooling water supply
must always follow the cutting process!
• When working at dry-cutting, make sure of sufcient
dust removal.
• When unhealthy or explosive substances are
released (dust, sludge) observe the national safety
regulations!
• Moving the machine outside the working area may
only be done with the saw blade removed!
• When the machine is to be driven on public
highways, roads and places, the relevant trafc laws
must be observed and, if necessary, make sure that
the machine complies with the relevant road vehicle
regulations!
• Do not drive transversely across inclines steeper
than 5%!
• Inclines steeper than 10% may only be negotiated
with the aid of one or more safety lines!
• Before moving the machine, always make sure that
the accessories are safely stored!
• When leaving the machine unattended, it must
always be secured against being switched on again
accidentally!
3.7 Special- and maintenance work
• Observe the adjustment, maintenance and inspection
work and intervals set down in the operating manual,
including the specications for the replacement of
part and assemblies. This work may only be carried
out by specially trained personnel!
• Inform the operating personnel before the start
of special- and maintenance work! Name the
responsible supervisor!
• During all work concerning the operation, adaption
for production, conversion or adjustment of the
machine and its safety-related equipment, as well as
inspection, maintenance and repair work, observe
the procedures for switching the machine on and
off as described in the operating manual and the
information on performing maintenance work!