0-5492 2-3 INTRODUCTION
2.05 Description
This CIGWELD WeldSkill 155 and 185 offer the
many benefits of a professional welding machine
in a compact, portable, easy to use and affordable
self-contained single phase welding inverter. Ideal for
welders who want to do light fabrication, maintenance
and repairs or DIY around the home without
compromising on quality or safety. These multi-
process welding inverters are capable of performing
MIG (FCAW/GMAW), Stick (MMAW) and Lift TIG
(GTAW) welding processes. The Weldskill 155 and
185 are backed by a 2 year warranty*, equipped with
a 10Amp plug, digital voltage and amperage meters,
an integrated wire feed unit, Voltage Reduction Device
(VRD applicable in Stick mode only), quick connect
gas connection and a host of other features. And
most importantly the two models are fully compliant
to Australian Standard AS 60974.1 and IEC 60974.1.
The WeldSkill 155 and 185 provide excellent welding
performance across a broad range of applications
when used with the correct welding consumables
and procedures. The following instructions detail how
to correctly and safely set up the machine and give
guidelines on gaining the best efficiency and quality
from the power sources. Please read these instruc-
tions thoroughly before using the units.
*NOTE
Refer to the complete Warranty Schedule at the
back of the manual..
2.06 User Responsibility
This equipment will perform as per the information
contained herein when installed, operated, maintained
and repaired in accordance with the instructions
provided. This equipment must be checked periodi-
cally. Defective equipment (including welding leads)
should not be used. Parts that are broken, missing,
plainly worn, distorted or contaminated, should be
replaced immediately. Should such repairs or replace-
ments become necessary, it is recommended that
such repairs be carried out by appropriately qualified
persons approved by CIGWELD. Advice in this regard
can be obtained by contacting accredited CIGWELD
Distributor.
This equipment or any of its parts should not be al-
tered from standard specification without prior written
approval of CIGWELD. The user of this equipment
shall have the sole responsibility for any malfunction
which results from improper use or unauthorised
modification from standard specification, faulty
maintenance, damage or improper repair by anyone
other than appropriately qualified persons approved
by CIGWELD.
2.07 Packaged Item
WeldSkill 155 Inverter (Part No. W1008155)
• WeldSkill 155 Inverter Power Source
• 3m Lead with Twist Lock Electrode Holder
• 3m Lead with Work Clamp
• E-180 MIG torch, 3m, Euro
• Feed Rolls: 0.8/0.9 Flux Cored (fitted)
0.8/0.9 V Groove
• Shielding Gas Hose
• Cutskill Argon Regulator/Flowmeter
• Operating Manual
WeldSkill 185 Inverter (Part No. W1008185)
• WeldSkill 185 Inverter Power Source
• 3m Lead with Twist Lock Electrode Holder
• 3m Lead with Work Clamp
• E-180 MIG torch, 3m, Euro
• Feed Rolls: 0.8/0.9 Flux Cored (fitted)
0.8/0.9 V Groove
• Shielding Gas Hose
• Cutskill Argon Regulator/Flowmeter
• Operating Manual
2.08 Transporting Methods
These units are equipped with a handle for carrying
purposes.
WARNING
ELECTRIC SHOCK can kill. DO NOT TOUCH live
electrical parts. Disconnect input power conductors
from de-energized supply line before moving the
welding power source.
!
WARNING
FALLING EQUIPMENT can cause serious personal
injury and equipment damage.
Lift unit with handle on top of case.
Use handcart or similar device of adequate capacity.
If using a fork lift vehicle, place and secure unit on a
proper skid before transporting.
To Next Page
Loading...
