Cisco ASR 1002 User Manual

Page 33 of 72
TOE-common-criteria(config-isakmp)# exit
TOE-common-criteria(config)# Crypto isakmp key cisco123!cisco123!CISC address
11.1.1.4
Note: Pre-shared keys on the TOE must be at least 22 characters in length and
can be composed of any combination of upper and lower case letters, numbers,
and special characters (that include: “!”, “@”, “#”, “$”, “%”, “^”, “&”, “*”,
“(“, and “)”).
The TOE supports pre-shared keys up to 127 characters in length. While longer
keys increase the difficulty of brute-force attacks, longer keys increase processing
time.
TOE-common-criteria (config-isakmp)# group 14
This selects DH Group 14 (2048-bit MODP) for IKE, but 19 (256-bit Random
ECP), 24 (2048-bit MODP with 256-bit POS), 20 (384-bit Random ECP), 15
(3072 bit MODP), and 16 (4096-bit MODP) are also allowed and supported.
TOE-common-criteria (config-isakmp)# lifetime 86400
The default time value for Phase 1 SAs is 24 hours (86400 seconds), but this
setting can be changed using the command above with different values.
TOE-common-criteria (config-isakmp)# crypto isakmp aggressive-mode disable
Main mode is the default mode and the crypto isakmp aggressive-mode disable
ensures all IKEv1 Phase 1 exchanges will be handled in the default main mode.
TOE-common-criteria(config-isakmp)#exit
4.6.1.2 IKEv2 Transform Sets
An Internet Key Exchange version 2 (IKEv2) proposal is a set of transforms used in the
negotiation of IKEv2 SA as part of the IKE_SA_INIT exchange. An IKEv2 proposal is regarded
as complete only when it has at least an encryption algorithm, an integrity algorithm, and a
Diffie-Hellman (DH) group configured. If no proposal is configured and attached to an IKEv2
policy, then the default proposal is used in the negotiation, and it contains selections that are not
valid for the TOE. Thus the following settings must be set in configuring the IPsec with IKEv2
functionality for the TOE:
TOE-common-criteria # conf t
TOE-common-criteria (config)#crypto ikev2 proposal sample
TOE-common-criteria (config-ikev2-proposal)# integrity sha1
TOE-common-criteria (config-ikev2-proposal)# encryption aes-cbc-128
This configures IPsec IKEv2 to use AES-CBC-128 for payload encryption. AES-
CBC-256 can be selected with ‘encryption aes-cbc-256’. AES-GCM-128 and
AES-GCM-256 can also be selected similarly.

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g