Basic Operations
.....................
Note:
Be sure
t6
read
this chapter referring to the front diagrams
of
chapter
"3.
CONTROLS" on page 5 (unfold).
Radio
mode
-+
CD
mode
-+
Tape
mode
-+
CD
changer
mode
-+
MD
changer
mode
-+
TV
mode
-+
AUX
mode
-+
Radio
mode
...
",
External equipment not connected with CeNET
is
not displayed.
]
]
[
[
Clock(CT) display
Sub
(title) display
~
Main display
':'
Once selected, the preferred display becomes
the display default. When a function adjustment
such as volume
is
made, the screen will mo-
mentarily switch
to
that function's display, then
revert back to the preferred display several
seconds after the adjustment.
':'
When you have entered a title
in
a
CD,
it
ap-
pears
in
the sub display.
If
you have not en-
tered a title, "NO-TTL" appears
in
the title dis-
play instead. For information
on
how
to
enter a
title, refer
to
the subsection
"Entering
titles"
in
the
"Operations
Common
to
Each Mode".
':'
You
can adjust the way of scrol!ing a title. For
the details
on
it,
refer
to
the subsection
"Ad-
justing
the
way
of
scrolling"
in
the
"Operations
Common
to
Each Mode".
Switching
the
display
Press the [DISP] button to select the desired dis-
play.
Each
time
you
press
the
[DISP] button, the dis-
play
switches
in
the
following order:
Main display
Adjusting
the
volume
Turn
the
[VOLUME]
knob
clockwise
to
increase
the
volume,
or
turn
the
[VOLUME]
knob
coun-
terclockwise
to
decrease
the
volume.
)
",
The volume level
is
from 0 (minimum) to 33 (maxi-
mum).
Selecting
a
mode
1.
Press
the
[FNC] button to
change
the
mode
of
operation.
2.
Each
time
you
press
the
[FNC] button,
the
mode
of
operation
changes
in
the
following
order:
Turning
on/off
the
power
Notes:
• Be careful about using this unit for a long time with-
out running the engine.
If
you drain the car's bat-
tery too
far,
you may not be able
to
start the en-
gine
and
this can reduce the service life
of
the
battery
• System check
This unit checks what external equipment
is
con-
nected
to
the CeNET The first time the ACC/lgni-
tion is turned on (initialization), "SYSTEM"
and
"Push PWR"alternately blink
in
the display Press
the [FNC} button
to
start the system check. When
complete, press the [FNC} button again
to
activate
the unit then the unit appears CHECKING COM-
PLETE.
1.
Press
the
[FNC] button.
2.
The
illumination
and
display
on
the
unit
light
up.
The
unit
automatically
remembers
its last
operation
mode
and
will
automatically
switch
to
display
that
mode.
3.
Press
and
hold
the
[FNC] button for 1
second
or
longer
to
turn
off
the
power
for the unit.
Be
sure
to
lower
the
volume
before
switch-
ing
off
the
unit
power
or
the
ignition
key. The
unit
remembers
its
last
volume
setting.
If
you
switch
the
power
off
with
the
volume up, when
you
switch
the
power
back
on,
the
sudden
loud
volume
may
hurt
your
hearing
and
dam-
age
the
unit.
The
clock
is
displayed
when
the
ignition
key
is
turned
to
the
ACC
(accessory)
or
IGN
(igni-
tion-on)
position
even
when
the
unit
power
is
off. In
some
cars,
the
clock
may
momentarily
disappear
when
the
ignition
key
is
turned
to
the
START
position.
The
clock
will
reappear
after
the
engine
has
started
and
the
ignition
key
is
released
to
the
IGN
(ignition-on)
posi-
tion.
12
AOZ625
To Next Page
Loading...
Need help?
General
