Operation
Common
to Each Mode
Setting
the
clock
1. Press and hold
the
[T] button for 1
second
or
longer
to
switch to the
adjustment
selection
display.
2. Press
the
[~>
] button
or
the [<
......
]button to
select
"CLOCK
I)".
3. Press the
[~II]
button.
4. Press the
[~>]
button
or
the
[<
......
] button to
select the
hour
or
the
minute.
5. Turn the
[VOLUME]
knob
either
clockwise
or
counterclockwise
to set the
correct
time.
*The clock
is
displayed
in
12-hour format.
6. Press the
[~II]
button to store the time into
memory.
7.
Press
the
[T] button
to
return
to
the previous
mode.
Note:
•
You
cannot set the clock when it is displayed with
only the ignition
on.
If
you drain
or
remove the car's
battery
or
take out this unit, the clock is reset. While
setting the clock,
if
another button
or
operation is
selected, the clock
set
mode is canceled.
Switching
the
spectrum
analyzer
display
patterns
You
can
select
one
out
of 8
patterns
or
set it to
off.
*The factory default setting
is
"PATTERN 1".
Each
time
you
press
the
[SPE/ANA]
button,
the
spectrum analyzer display pattern
changes
in
the
following
order:
PATTERN 1
~
PATTERN 2
~
PATTERN 3
~
PATTERN 4
~
PATTERN 5
~
PATTERN 6
~
PATTERN 7
~
SCAN
~
OFF
~
PATTERN 1
...
Note:
The
spectrum analyzer display
is
unavailable during
these operations below;
• Seek tuning
and
auto store
in
radio mode.
• Mute
or
pause.
• When "NO DISC"
or
an error message appears
in
the display.
Setting
the
sensitivity
of
the
spectrum
analyzer
*The factory default setting
is
"MID".
1. Press and hold
the
[T] button for 1
second
or
longer
to
switch to
the
adjustment
selection
display.
2. Press the
[~>
] button
or
the [<
......
]button to
select
"ANA
SENS".
20
ADZ625
3. Turn the [VOLUME]
knob
either
clockwise
or
counterclockwise
to set the sensitivity of the
spectrum
analyzer.
You
can
choose
one
of
"LOW",
"MID"
or
"HIGH" for the sensitivity of the
spectrum
ana-
lyzer.
4. Press the [T] button to return to the previous
mode.
Setting
the
speed
of
the
spectrum
analyzer
display
:,:
The factory default setting
is
"HIGH".
)
1.
Press and hold the [T] button for 1
second
or
longer
to switch to the
adjustment
selection
display.
2. Press the
[~>
] button or the
[<
......
]
button~to
select
"ANA
SPD".
3. Turn the [VOLUME]
knob
either
clockwise
or
counterclockwise to set the speed of the spec-
trum
analyzer
display.
You
can
choose
one
of
"LOW",
"MID"
or
"HIGH" for the
speed
of the
spectrum
ana-
lyzer display.
4.
Press the [T] button to return to the previous
mode.
Entering
titles
Titles up to 10
characters
long can be stored
in
memory
and displayed for radio or
TV
stations
and CDs.
The
numbers
of titles
that
can be en-
tered for each
mode
are as follows.
Mode
Number
of
titles
Radio
mode
30 titles
CD
mode
100
titles
TV
mode
15 titles
CD
changer
mode
Number
of
titles
CDC655z
connected
60 titles
CDC655Tz
connected
100 titles
CDC1255z
connected
50
titles
1.
Press the [FNC] button to select the mode you
want to enter a title. (radio, CD, CD changer or
TV)
:,:
Titles cannot be entered for MDs with this unit.
2.
Select and
playa
CD or a CD
in
the CD changer,
or tune to an appropriate
TV
or radio station.
3. Press the
[DISP] button and display
the
title.
4. Press the [T] button. "TITL"
appears
in the dis-
play and the
cursor
position flashes.
To Next Page
Loading...
