System
Setup
S-CTRL
(IPod
mode):
ON/OFF
Rotate the
[CONTROL]
knob
to choose
S-CTRL
(Simple control)
ON
or
OFF.
* Refer
to
P12.
RESET
1.
Select
"RESET".
2. Press and
hold
the
[CONTROL)
knob
to
reset.
3.
Settings will
be
set
to
the
default value.
4.
The
unit
will
be
turned off
automatically.
Note:
•
When
the
[RESET]
is
selected
and you
press and
hold
the
[CONTROL)
knob, radio
station frequencies,
titles, and other
data
stored
in
memory are
cleared.
Audio
Setup
SOUND
Press
the
(CONTROL]
knob
to
choose
SOUND
.
First press
shows
current EO. Rotate
the
(CONTROL]
knob
to
choose BEAT EO
in
this order:
OFF
->
B-BOOST
->
IMPACT->
EXCITE
->
CUSTOM
To
change
CUSTOM
setting
,
and
press
the
(CONTROL]
knob
(center)
,
then
press
[CONTROL]
knob
(right/left)
to
select
EO
effects
including
:
BASS-G
->
BASS-F
->
BASS-O
->
M I
D-G
->
M
I
D-F
->
M
I
D-Q
->
TREBLE-G
->
TREBLE-F.
rotate
the
(CONTROL]
knob
to
select
a
value.
BASS-G
I
MID-G
I
TREBLE-G
: (-7)- (+7)
BASS-F:
50
I
100
I
200
BASS-O :
0.7/1.0/1
.
4/2.0
MID-F:
500/1
K
I
2 K
8
M502
MID-0:
0.
7/1
.
0/1
.
4/
2.0
TREBLE-F
: 5 K
/10
K
/15
K
TREBLE-Q:
0.
7/1.0/1.4/2
.0
Then press
the
(CONTROL]
knob
(left
I
right) to
select
USER preset
including:
BALANCE
->
FADER
-> M-B EX
->HPF(high
pass
filter)
->
LPF(Iow
pass
filter)
->
S-W
VOL
(Subwoofer
Volume),
rotate
the
(CONTROL]
knob to select
a
value.
BALANCE: LEFT 1-7 ->CENTER->RIGHT
1-7
FADER:FRONT
1-7->CENTER->REAR 1-7
M-B EX: ON/OFF
HPF: THROUGH/60/90/120
LPF: THROUGH/60/901120
SUBW
VOL:
(-6)-(+6)
Radio Operations
Select tuner
as
playing
source
Press
the
(CONTROL]
knob
or
(SAC
I
<!>]
button on the remote
control
to
switch
to
the
RADIO
source.
Select one radio
band
Press
the
the
(CONTROL]
knob (up
long
press) on the
panel
or
[BAND/TOP]
button
on
the
remote
control
to
select
one radio
band
among FM1, FM2, FM3 and AM.
Manual tuning
During
manual
tuning,
the
frequency
will
be
changed
in
steps.
Press
[CONTROL]
knob
(left/right)
on
the
panel
or [
~
,
....
] buttons on the remote
control
to
tune
in
a higher
I
lower
station.
Auto
tuning
Press and
hold
[CONTROL]
knob
(left/right}
on
the
panel
or [
~
,
....
] buttons the remote
control
to
seek
a higher
I
lower
station.
To
stop searching, repeat the operation
above or press other buttons having radio
functions.
Note:
When
a station is received, searching
stops
and
the
station is
played.
Preset scan
Preset scan receives the stations
stored
in
preset memory
in
order.
This
function is
useful
when searching for a desired station
in
memory.
1.
Press the
(SCN/PS/AS]
button on the
remote
control.
2.
When
a desired station is tuned in, press
the
(SCN/PS/AS]
button on the remote
controlagain
to continue receiving that
station.
Note:
Be
careful
not to press and
hold
the
[SCN/PS/AS]
button, otherwise the auto
store
function is engaged and the unit starts
storing stations.
Auto
store
Only
stations with sufficient signal
strength
will
be
detected and
stored
in
the
memory.
Press and
hold
the
[SCN/PS/AS]
button on
the
remote
control
to
start
automatic station search.
To
stop auto store, press other buttons having
radio functions.
Notes:
1. After auto store,
the
previous
stored
stations
will
be
overwritten.
2.
The
unit
has
4 bands,
such
as
FM1, FM2,
FM3 and AM. FM3 and AM can store
by
AS
function. Each bands can
store
6 stations,
M502
can
store
24 stations
in
total.
Manual store
When
one expected radio station
has
been
detected, press and hold
number button on
the
remote
contro11-6
to
store
it
in
the memory.
Recall
the
stored
stations
Press one numeric button among 1
to
6 on
the
remote
control
or on the
panel
to
select
the
corresponding
stored
station.
Local
seeking
When
LOCAL
seeking is on,
only
those radio
stations with strong radio
signal could
be
received.
Refer
to
System Setup page 7.
Note:
The
number of radio stations that can
be
received
will decrease
after
the
local
seeking
mode
is
on.
To Next Page
Loading...
Need help?
General
